manualshive.com logo in svg

LEGRAND STARK 10 kVA, Installation And User Manual, Page: 22 / 52

Share
Download
LEGRAND STARK 10 kVA Installation And User Manual Download Page 22

22

 

ώ

Switch ON the output breaker.

 

ώ

Switch ON the input breaker. 

The UPS powers from the static bypass instead of the maintenance bypass, then the 

bypass LED will light up.  

 

ώ

Switch OFF the maintenance bypass breaker, then the output is supplied by the static 

bypass of the UPS. 

 

ώ

Put on the maintenance switch cover. 

The rectifier will operate normally after 30 seconds.  If the inverter works normally, the 

system will be transferred from bypass mode to normal mode.  

 

ώ

Set the Battery Breaker to the “ON” for long run UPS. 

 

ώ

Switch ON the power switch for standard UPS.

 

ώ

Turn on the Output switch.

 

ώ

Switch ON the power switch (power will feed to auxiliary power board).

 

ώ

Trigger the cold start button as the position 5 of the below drawing.

When battery normal, rectifier starts operation, 30s later, inverter starts and operates and 

battery LED on

4.2.4 Cold start procedure

CAUTION: 

 

Follow these procedures when the input AC Utility Failure, but 

battery is normal

1

2

3

4

5

POWER

Summary of Contents for STARK 10 kVA





















































Reviews:

No comments