manualshive.com logo in svg

LEGRAND STARK 10 kVA, Installation And User Manual, Page: 14 / 52

Share
Download
LEGRAND STARK 10 kVA Installation And User Manual Download Page 14

14

10kVA factory setting of the long-run unit is battery quantity---16pcs, battery capacit-

y---12V9AH (charger current 1.35A). When connecting 18/20 batteries, please re-set desi-

red battery quantity and its capacity after UPS starts at AC mode. Charger current could be 

adjusted automatically according to battery capacity selected. All related settings can be 

done through LCD panel or monitoring software 

15-20kVA factory setting of the long-run unit is battery quantity---32pcs, battery capacit-

y---12V18AH (charger current 2.7A). When connecting 32/34/36/38/40 batteries, please re-

set desired battery quantity and its capacity after UPS starts at AC mode. Charger current 

could be adjusted automatically according to battery capacity selected. All related settings 

can be done through LCD panel or monitoring software

The following sections introduce the installation procedures specified 

to the parallel system.

CAUTION: 

 

Ensure correct polarity battery string series connection. 

I.e. inter-tier and inter block connections are from (+) to 

(-) terminals. Don’t mix batteries with different capacity 

or different brands, or even mix up new and old batteries, 

either.   

WARNING: 

 

Ensure correct polarity of string end connections to the 

Battery Circuit Breaker and from the Battery Circuit 

Breaker to the UPS terminals i.e. (+) to (+) / (-) to (-) but 

disconnect one or more battery cell links in each tier. Do 

not reconnect these links and do not close the battery 

circuit breaker unless authorized by the commissioning 

engineer.

3.9 UPS PARALLEL INSTALLATION

3.9.1 Cabinet installation

Connect all the UPS needed to be put into parallel system as below picture.

UPS1

UPS2

UPS3

UPS4

AC INPUT

AC OUTPUT

Summary of Contents for STARK 10 kVA





















































Reviews:

No comments