background image

If   the   film   curls   up   as   it   leaves   the   machine,   loosen   the   top   supply   roll 
mandrel   (turn   counterclockwise)   and/or   tighten   the   bottom   supply   roll 
mandrel (turn clockwise).
If the film curls down after it leaves the machine, tighten the top supply roll 
mandrel (turn clockwise) and/or loosen the bottom supply roll mandrel (turn 
counter-clockwise).   In making these adjustments, make sure that top and 
bottom supply roll tension are kept about equal.

8.  When running films of 3 mil or above turn the fans on before beginning to 
laminate.     “Waves”   or   “ripples”   tending   to   run   through   the   center   of   the 
laminated web are usually caused by forgetting to run the fans or setting too 
high a temperature for the film being used.

“Heat   wrinkles”

  are   formed  when   the  film   as  not   cooled   enough   before 

coming out the back of the machine.  For the best results the film should be 
cooled   below   melt   temperature   while   it   is   pulled   tight   and   perfectly   flat 
between the laminating rollers and the pull rollers.  If it gets out the back of 
the machine while still at or above melt temperature heat wrinkles can form. 
The major reason for fans on a laminator is to cool the laminate not to cool 
the machine.

9.  

  This   machine   is   equipped   with   a   directional   switch: 

forward/neutral/reverse.     Turn   to   the   forward   position   to   laminate,   or   to 
reverse as required.  The manufacturer recommends the stop switch be used 
to stop the laminator rather than the neutral position of the directional switch. 
To   remove   anything   which   may   become   lodged   between   the   rubber 
laminating or pull rollers, remove the feed tray assembly and open rollers. 
Switch control to reverse if required.

10.  A unique feature of the laminator is the provision for driving both top and 
bottom  pull   rollers   and  laminating   rollers.    This  feature   provides  an  even 
distribution of heat on a continuous basis to the laminating rollers prior to 
startup or when laminating production is temporarily halted. 

The   laminator   becomes   capable   of   accepting   thick   materials,   without   roll 
slippage because the top and bottom rollers are driven.  Driven rollers also 
minimize the “curling effect” in the finished lamination by providing balanced 
power to the laminating and pull rollers.

11. The laminator is designed to operate with the operator directly facing the 
control panels and feed tray assembly.

For   operator   safety   the   feed   table/heat   shoe   guard,   an   integral 
component   of   the   feed   table   assembly,     MUST     BE     IN     ITS 
DESIGNATED  POSITION  when the temperature of the heat shoes is in 

27

Summary of Contents for HD-25





















































Reviews: