- 6 -
When two Lazer Links are in intercommunication,
the incoming call functions with the respective
mobiles are maintained. If you receive an incoming
call the Intercom stops and when the call ends it
returns. The other device in Intercom, which is not
receiving the call, will receive an acoustic warning
signal. If you wish to make a call, you have to
deactivate the intercom first.
INTERCOM FUNCTIONS BETWEEN TWO LAZER LINK
ACTIVATE AND DEACTIVATE INTERCOM
When both Lazer Links are in a range of less than
10 metres from one another, switched on and
paired with their respective mobiles, in order to
establish the connection in Intercom, press the
control button (A) of one of the devices for a
couple of seconds, until you hear an acoustic
signal. The intercommunication between the two
Lazer Links will be activated then. To deactivate the
intercommunication, press the control button (A) of
one of the Lazer Links for a couple seconds.
INTERCOM VOLUME ADJUSTMENT
The Lazer Links allow changing their volume level
when they are in Intercom. Each time you press the
control button (A) the volume level changes in a
cycle of three levels (low -> medium -> high -> low...)
PAIRING IN INTERcom WITH ANoTHER DEVIcE
oR ANoTHER AUDIo REcEIVER BLUETooTH
®
DEVIcE (LAZER BLUE oR LAZER RINGo)
Make sure that the two devices to be associated
are switched off. Press and keep the control button
(A) of the Lazer Link pressed until the LED (A1) starts
to flash in Red and Blue. Set the other Bluetooth
®
device in pairing mode. Then briefly press the
control button (A) of the Lazer Link once. After a
few seconds, both devices are paired and you
can establish the intercommunication. When they
have been associated, we recommend to switch
off the Lazer Link and to switch on the other devices
(GPS, Mobile, etc), then turn the Lazer Link back on
and activate the intercom function by pressing 2
seconds on the control button (A).
When the Lazer Link is in intercommunication,
the incoming call functions with your mobile are
maintained. If you receive an incoming call the
Intercom stops and when the call ends it returns.
The other device in Intercom will receive an acoustic
warning signal. If you wish to make a call with the
Lazer Link you have to deactivate the Intercom first.
INTERCOM FUNCTIONS WITH ANOTHER DEVICE
OR ANOTHER AUDIO RECEIVER BLUETOOTH
®
DEVICE
(LAZER BLUE OR LAZER RINGO)
ACTIVATE AND DEACTIVATE INTERCOM
The Lazer Link can activate or deactivate
intercommunication with another Bluetooth
®
device. To establish a connection in Intercom,
the two devices should be in a range of less than
10 metres from one another, switched on and
paired. Then press the control button (A) on the
Lazer Link for a couple of seconds until you hear an
acoustic signal. The intercommunication will then
be activated. To deactivate it press and keep the
control button (A) of the Lazer Link pressed for a
couple of seconds.
INTERCOM VOLUME ADJUSTMENT
The Lazer Links allow changing their volume level
when they are in Intercom. Each time you press the
control button (A) the volume level changes in a
cycle of three levels (low -> medium -> high -> low...)
SPEcIFIcATIoNS
Bluetooth
®
: 2.1 Class 2
Profiles: A2DP, HSP, HPF, EDR.
Battery: Lithium polymer, that will provide up to
7 hours talk time and up to 200 hours standby
time (depending on configuration and use of the
device).
cARE AND mAINTENANcE
Lazer Link uses the latest technology and is
manufactured to the highest quality standards.
Observing the following recommendations will
ensure that Lazer Link is not inadvertently damaged.
- Do not try to open any of the system components,
as the electronic parts inside may be damaged.
Additionally, trying to open or modify the battery
is dangerous.
- Keep your Lazer Link out of reach of children.
- Keep your Lazer Link in a dry place. Steam and
humidity may damage the electronic circuits.
- Avoid extreme heat or cold. Extreme cold may
cause condensation inside the components
when re-warmed. Extreme heat may damage the
battery, circuits or casings.
- Do not drop, hit or twist the components, as the
circuits inside may be damaged.
- Do not paint or decorate the Lazer Link, as it may
damage the casing or prevent the intercom from
functioning correctly.
- Do not use chemicals, solvents or detergents to
clean the Lazer Link as it may damage the casing.
MEG Lazer Link bichro DEF 2.indd 6
12/12/12 14:23