- 4 -
UK
WELcomE
Congratulations and thank you for choosing the
Lazer Link, the innovative handfree Bluetooth
®
system especially designed for the Lazer helmets
to allow easy and safe audio communication in
motion.
The Lazer Link is compatible with all audio
Bluetooth
®
transmitting devices in HSP, HFP and
A2DP profiles (Mobile, GPS, MP3, MP4, or any
device compatible with all of the aforementioned
functions). It can also be associated (paired)
with any Bluetooth
®
audio receiver device, or
to another Lazer Link, establishing an audio
communication (intercommunication) up to a
distance of approximately 10 metres, maintaining
the association with the mobile or corresponding
device at the same time.
This device can be fully operated with only one
control button (A). A single LED (red/blue) (A1)
is the indicator of its functions: pairing, charging,
on/off, low battery indicator. The Lazer Link weighs
only 55g approximately. In order to get the best
use out of your Lazer Link, please read this manual
thoroughly, and then keep it in a safe place for later
use or visit
http://www.lazerhelmets.com/fr/innovations-2/lazer-link
cHARGING THE LAZER LINK
Before using the Lazer Link for the first time, the
battery (D) must be fully charged. Plug the charger
(F) into the socket, and then insert the other end of
the cable to the Lazer Link mini-USB jack (B)
While the battery is charging the red LED (A1) is on,
and will turn off once it is fully charged.
NOTE: Never unplug the devices by pulling from the cable.
NOTE: It is recommended to completely charge
the battery each time, this will extend the battery
life time.
NOTE: When the battery is charged completely but
has not been used for a long time, it may have
less energy storage than normal. After being used
and recharged a few times, the energy storage will
increase back to normal.
INSTALLING THE LAZER LINK
See the video on “how to install the Lazer Link” on
our website:
http://www.lazerhelmets.com/fr/innovations-2/lazer-link
PAIRING WITH A moBILE oR NAVIGAToR (GPS)
To be able to use the Lazer Link you have to
associate it with the Bluetooth
®
device you want to
connect it to (Mobile, GPS, etc). To do this, when
the Lazer Link is switched off, press and keep the
control button (A) pressed until the LED (A1) starts
to flash alternately in Red and Blue. When looking
for Bluetooth
®
devices in the mobile or navigator,
you should find the device called “Lazer Link”.
Select the “Lazer Link” device and if requested enter
the 0000 access code.
SWITCHING ON / SWITCHING OFF
To switch on your Lazer Link press and hold the
control button (A), until you hear a beep audio
sound in the speaker (C) and the LED (A1) starts to
blink in a blue colour.
To switch off your Lazer Link press and hold the
control button (A) for a couple of seconds, until you
hear a beep sound in the speaker and the LED (A1)
starts to blink in a red colour and then off.
cALL FUNcTIoNS
ANSWERING AND ENDING A CALL
When there is an incoming call, the speaker will
play an acoustic signal.
To answer the call, you can say any word out loud
into the microphone (E) (for example:” Answer!”) or
press the control button (A) just once, or, as long
as your mobile phone allows it, you can activate
the automatic answering function on the mobile
phone.
To end the call, press the button (A) just once or
wait for the caller to hang up.
REJECTING AN INCOMING CALL
To reject an incoming call, you just have to press
the control button (A) twice when you hear a call
acoustic signal.
MAKING A CALL
To make a call, press the control button (A) to
activate the voice dialing function of the associated
mobile (the mobile should be configured to allow
voice dialing, as long as the mobile has this
function).
To make a re-call (repetition of the last dialed
number), press the control button twice (A).
It also depends on the mobile’s functions and
configuration.
VOLUME ADJUSTMENTS
WITH MOBILE OR NAVIGATOR (GPS)
The Lazer Link device comes programmed with a
volume level that allows perfect listening up to 120
km/h. Use the volume control of the associated
device to adjust the volume. It is recommended
to set the highest volume level of the Lazer Link
with the control button (A) before the connection
of the other device
(see ??? “INTERCOM VOLUME
ADJUSTMENT”)
MEG Lazer Link bichro DEF 2.indd 4
12/12/12 14:23