- 5 -
NOTE: Never unplug the devices by pulling from the cable.
NOTE: It is recommended to completely charge
the battery each time, this will extend the battery
life time.
NOTE: When the battery is charged completely but
has not been used for a long time, it may have
less energy storage than normal. After being used
and recharged a few times, the energy storage will
increase back to normal.
INSTALLING THE LAZER LINK
See the video on “how to install the Lazer Link” on
our website:
http://www.lazerhelmets.com/fr/innovations-2/lazer-link
PAIRING WITH A moBILE oR NAVIGAToR (GPS)
To be able to use the Lazer Link you have to
associate it with the Bluetooth
®
device you want to
connect it to (Mobile, GPS, etc). To do this, when
the Lazer Link is switched off, press and keep the
control button (A) pressed until the LED (A1) starts
to flash alternately in Red and Blue. When looking
for Bluetooth
®
devices in the mobile or navigator,
you should find the device called “Lazer Link”.
Select the “Lazer Link” device and if requested enter
the 0000 access code.
SWITCHING ON / SWITCHING OFF
To switch on your Lazer Link press and hold the
control button (A), until you hear a beep audio
sound in the speaker (C) and the LED (A1) starts to
blink in a blue colour.
To switch off your Lazer Link press and hold the
control button (A) for a couple of seconds, until you
hear a beep sound in the speaker and the LED (A1)
starts to blink in a red colour and then off.
cALL FUNcTIoNS
ANSWERING AND ENDING A CALL
When there is an incoming call, the speaker will
play an acoustic signal.
To answer the call, you can say any word out loud
into the microphone (E) (for example:” Answer!”) or
press the control button (A) just once, or, as long
as your mobile phone allows it, you can activate
the automatic answering function on the mobile
phone.
To end the call, press the button (A) just once or
wait for the caller to hang up.
REJECTING AN INCOMING CALL
To reject an incoming call, you just have to press
the control button (A) twice when you hear a call
acoustic signal.
MAKING A CALL
To make a call, press the control button (A) to
activate the voice dialing function of the associated
mobile (the mobile should be configured to allow
voice dialing, as long as the mobile has this
function).
To make a re-call (repetition of the last dialed
number), press the control button twice (A).
It also depends on the mobile’s functions and
configuration.
VOLUME ADJUSTMENTS
WITH MOBILE OR NAVIGATOR (GPS)
The Lazer Link device comes programmed with a
volume level that allows perfect listening up to 120
km/h. Use the volume control of the associated
device to adjust the volume. It is recommended
to set the highest volume level of the Lazer Link
with the control button (A) before the connection
of the other device
(see ??? “INTERCOM VOLUME
ADJUSTMENT”)
LISTENING TO THE MOBILE'S MUSIC
After connecting the Lazer Link to the mobile
phone that can play music by Bluetooth
®
, when
the music is activated in the mobile it will be
immediately heard through the Lazer Link device.
The music and the volume can only be controlled
from the mobile phone depending on its functions
and configuration. All of the call functions are
maintained when you are listening to music. If you
receive an incoming call, the music stops and
when the call ends it returns. The same happens
when you make a call.
PAIRING IN INTERcom
WITH ANoTHER LAZER LINK DEVIcE
Make sure that the two Lazer Links are switched off
(switch off as well any Bluetooth
®
device that could
be associated to the Lazer Link, such as mobile
phone, GPS, etc.) Press and keep the control
button (A) of both Lazer Links pressed until the LEDs
(A1) on both devices start to flash alternately in Red
and Blue. Then, briefly press the control button of
one of the Lazer Link devices. After a few seconds,
both devices are paired and you can establish the
intercommunication.
When they have been associated, we recommend
switching off both Lazer Links and switching on the
other devices associated to each Lazer Link (GPS,
mobile, etc.) then, switch the Lazer Links back on,
end the activation of the Intercom function by
pressing 2 seconds on the control button (A) of one
of the Lazer Links.
N.B.: It is important to associate each Lazer Link
to its respective Bluetooth device (GPS, mobile,
etc) before the association of the two Lazer Links
between themselves.
MEG Lazer Link bichro DEF 2.indd 5
12/12/12 14:23