OWNER’S MANUAL
EYEWEAR
A
C
B
D
Magneto 3 & Eddy (M3)
A
C
B
D
Magneto 2 & Krypton 1 (M2 & KR1)
Magneto 1 & Radon 1 (M1/M1-S & RN1)
A
B
Solid State 1 (SS1)
A
B
A
A
B
B
Walter & Walter Large
Argon 2 & Argon Race (AR2 & ARR)
LIMITED WARRANTY
Lazer Eyewear is warranted for one year from
the date of purchase against all manufacturer
defects. Lazer will replace or repair free of
charge with proof of purchase of any Lazer
Eyewear found to be defective during the
warranty period. This warranty will not apply
to any defect or damage caused by improper
or unreasonable use of the eyewear.
Lazer Eyewear lenses are not warranted
against scratching. All warranties that are
implied by the law are also limited to one year
from date of purchase.
CARE FOR YOUR LAZER EYEWEAR
When not in use, store your Lazer Eyewear
in either the hard or soft case included when
purchased. Lazer Eyewear frames and lenses
should be cleaned with warm water and a
mild soap. To avoid lens scratching, rinse the
lenses first before cleaning to remove any
debris or salt residue.
Do not store your Lazer Eyewear in extreme
hot or cold environments for extended
periods.
—
All Lazer Eyewear comply to CE 89/686/EEG,
EN ISO 12312-1:2013 + A1:2015,
AS/NZS 1067:2003 and ANSI Z80.3:2010.
ENGLISH
Crystal photochromic lens:
Type of filter: photochromic
Filter category: category 1 - category 2
Light transmission: 75% - 25%
Polarized lens:
Type of filter: polarized
Filter category: category 3
Light transmission: 12%
Clear lens:
Type of filter: standard
Filter category: category 0
Light transmission: 98%
Melanin photochromic lens:
Type of filter: photochromic
Filter category: category 2 - category 3
Light transmission: 31% - 12%
Yellow lens:
Type of filter: standard
Filter category: category 1
Light transmission: 70%
All other lenses:
Type of filter: standard
Filter category: category 3
Light transmission: 18%
Note
Restriction of use for all lenses:
· Not for direct observation of the sun
· Not for protections against artificial
light sources e.g. solaria.
· Not for use as eye protection against
mechanical hazards such as impact.
None of the lenses are suitable for
driving in twilight or at night, except for
the clear lens.
LENS CHANGING INSTRUCTIONS FOR LAZER EYEWEAR
Note: The lenses of X1, WAY1, WAY2, WAY3, Frank, Blub & Kidi are not made to be removed. If you do remove them, the warranty expires.
A. Removing lenses:
With one hand, hold the top of the frame on
the outside, and hold the lens with your other
hand.
Pull the frame upwards and away with one
hand, while holding the lens firmly in place
with the other hand.
Repeat this on the other side.
Then, hold the upper rim of the frame with
one hand, and hold the lens with the other.
Now gently pull the upper rim of the frame
upwards, and pull out the lens. Finally, loosen
the lens from the nosepiece with a rotating
motion.
B. Replacing lenses:
Place the lens over the nose bridge and push
it downwards into the correct position. Make
sure that the upper rim fits neatly around the
lens. Then, push the lips into the groove,
against the spring. Repeat this on the other
side.
C. Removing springs from glasses:
Hold the frame with one hand, and hold the
spring with the other. Push the spring inwards
and put pressure on the longest pin of the
spring while loosening it with a rotating moti-
on. Repeat this for the other side.
D. Replacing springs in the glasses:
Hold the frame with one hand, and hold the
spring with the other.
Insert the spring’s longest pin into the lower
hinge hole of the frame. Then, slide the
spring’s uppermost pin through the slot so
that it clicks into the uppermost hole.
Repeat this for the other side.
A. Removing lenses:
Face the glasses downwards, and open up
the springs. Hold the glasses with both hands
on the top and bottom of the frame. Place
your fingers on the front of the frame and rest
your thumbs on the glass.
Carefully pull apart the frame and softly push
the lens out of the frame with your thumbs.
Repeat this for the other lens.
B. Replacing lenses:
Face the glasses upwards and slide the lens
into the uppermost groove, towards the nose
bridge. Slide the lens further into the groove
on the frame and push on it gently until the
lens is fully inserted into the frame.
Repeat this for the other lens.
C. Removing springs from glasses:
Hold the frame with one hand, and hold the
spring with the other. Push the spring inwards
a little, and put pressure on the longest pin of
the spring to bend it, while loosening it with a
rotating motion.
Repeat this for the other side.
D. Replacing springs in the glasses:
Hold the frame with one hand, and hold the
spring with the other.
Insert the spring’s uppermost pin (the largest)
into the uppermost hinge hole of the frame.
Then, slide the spring’s lowest pin through the
slot so that it clicks into the lowest hole.
Repeat this for the other side.
A. Removing lenses:
With one hand, hold the lens by the upper rim near
the connection between the lens and the spring.
Hold the spring with the other hand. Carefully pull
the spring downwards and away from the lens, so
that the lens is loosened from the frame. Repeat
this for the other side.
B. Replacing lenses:
Slide the lowest lip of the lens into the lowest
groove of the spring. Turn the spring upwards so
that the lens clicks into the uppermost groove of
the spring. Repeat this for the other side.
A. Removing lenses:
With one hand, hold the top of the frame on
the outside, and hold the lens with your other
hand.
Pull the frame upwards and away with one
hand, while holding the lens firmly in place
with the other hand.
Repeat this on the other side.
B. Replacing lenses:
Slide one of the lips of the lens into one of the
frame’s corners in the direction of the hinge. Slide
the lens further into the groove on the frame, up to
the other lip. Pull the frame over the lip.
A. Removing lenses:
Face the glasses downwards, and open up
the springs. Hold the glasses with both hands
on the top and bottom of the frame. Place
your fingers on the front of the frame and rest
your thumbs on the glass.
Carefully pull apart the frame and softly push
the outside of the lens out of the frame with
your thumbs. Repeat this on the other side.
Then, repeat these steps for the middle of
the frame.
B. Replacing lenses:
Face the glasses upwards and slide the lens
around the nose bridge in the middle, then
push it gently into the grooves. Then, gently
push the rest of the lens into the grooves,
starting in the middle and moving outwards
toward the springs.
A. Removing lenses:
With one hand, hold one of the lenses on
the inside (level with the nosepiece) and with
the other hand hold the frame by the nose
bridge. Pull the frame up and over the lip, so
that the lens comes loose. Repeat this for the
other lens.
B. Replacing lenses:
The lenses must be inserted one by one.
Slide the lip of the lens into the frame by the
hinge. Hold the frame by the nose bridge and
pull it downwards, over the innermost lip.
PLEASE NOTE: The lens with ‘Lazer’ inscribed
on it must be inserted on the left hand side of
the frame.
Filter category
Description
Usage
0
Light tint
sunglasses
Very limited reduction
of sunglare
1
Limited
reduction of sunglare
2
General
purpose
sunglasses
Good protection against
sunglare
3
High protection against
sunglare
LENS INFORMATION
