Lattice Semiconductor MachXO5-NX Development Kit, User Manual

Page: 10 / 64

MachXO5-NX Development Board
Preliminary Evaluation Board User Guide
© 2022 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal .
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
10 FPGA-EB-02052-0.90
2. Applying Power to the Board
The MachXO5-NX Development Board comes ready to power up with onboard DC/DC switching regulators and Low
Dropout (LDO) generators powered by an external 12 V DC power source. The external power supply can be connected
with the DC power input jack J17, which is fused with a surface mounted fuse U10. The 1.25A fuse prevents the crashed
current from flowing into the internal circuits and cause serious damage. 12 V DC power also supply Arduino Header J4
and FX12 headers U4/U5 for the board extension, as shown in
Figure 2.1 .
Fuse (U10)
12V DC
USB Header
(J11)
5V DC
5V Regulator
(U11)
Slide Switch
(SW6)
5V
5V
12V
1.0V Regulator
(U12)
VCC Core(U3)
1.0V
2.5V LDO
(U13)
3.3V LDO (U8)
1.8V LDO
(U15)
1.2V LDO
(U16)
2.5V
1.2V
Raspberry Pi
Header(J6)
Arduino
Header(J4)
JP7
2.8V LDO
(U20)
VCCIO0/2(U3)
VCCIO1(U3)
JP6
J25
3.3V
3.3V
VCCIO3(U3)
2.5V
J26
3.3V
3.3V
VCCIO8(U3)
J23
3.3V
3.3V
VCCIO7(U3)
J22
3.3V
1.8V
VCCIO4(U3)
J29
1.2V
2.5V
VCCIO6(U3)
J21
1.2V
1.8V
VCCIO5(U3)
J20
1.8V
1.2V
5V
VCCIO9(U3)
1.8V
VCCAUX/VCCAUXA/VCCAUX
H/VCCADC (U3)
1.8V
FX12 Headers
(U4/U5)
Power Jack
(J17)
12V
5V
3.3V
1.8V
HyperRAM
(U6/U9)
JTAG(J1)
PMOD(J15)
JTAG(J18)
PMOD(J16)
SMGIIVDDIO(U7)
PMOD(J28)
30-pin
Header(J27)
2.8V
Figure 2.1. Board Power Supply
The onboard 5 V power regulator U11 provide 90% power convert efficiency from 12 V when output current between
50 mA and 3 A. It is distributed to 3.3 V, 2.8 V, 2.5 V LDOs and 1.0 V regulator through one side of slide switch SW6 to
support onboard devices. Through another side of SW6, this board can also take the 5 V power from USB header J11 as
well, for some low power application. It is user’s responsibility to ensure all 5 V power rails on board consume less than
500mA per PC’s USB port output capability when take power from J11.
For the board extension, 5 V DC power can also supply FX12 adapter, Raspberry Pi and Arduino boards through the
jumpers and onboard headers, to consolidate AC/DC adapters for stack boards system. Conversely, 5V DC power can
be either supplied from mated boards with correct jumper settings. However, maintain the 5 V DC power is the basic
requirement to bring up this board, by quick check the power good blue LED D18.
The onboard 1.2 V and 1.8 V LDOs take the power from 3.3 V and 2.5 V LDO correspondently.
Table 2.1 summarizes onboard major power rails and their test points.