Lattice Semiconductor ECP5 Versa Technical Note Download Page 69

Page: 69 / 86

ECP5 and ECP5-5G High-Speed I/O Interface

Technical Note

www.latticesemi.com/legal

All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.

FPGA-TN-02035-1.3

8.8.2.

IDDRX2F

This primitive is used to receive Generic DDR with 2x gearing.

SCLK

RST

ALIGNWD

ECLK

IDDRX2F

Figure 8.6. IDDRX2F Primitive

Table 8.10. IDDRX2F Port List

Port

I/O

Description

DDR data input

ECLK

Fast Edge Clock

SCLK

Primary Clock input (divide-by-2 of ECLK)

RST

Reset to DDR registers

ALIGNWD

This signal is used for word alignment. It shifts the word by one bit.

Q0, Q2

Data at positive edge of input ECLK

Q1, Q3

Data at negative edge of input ECLK

8.8.3.

IDDR71B

This primitive is used for 7:1 LVDS input side implementation.

SCLK

RST

ALIGNWD

ECLK

IDDR71B

Figure 8.7. IDDR71B

Table 8.11. IDDRX2F Port List

Port

I/O

Description

DDR data input

ECLK

Edge Clock

SCLK

Primary Clock (divide-by-3.5 of ECLK)

RST

Reset to DDR registers

ALIGNWD

This signal is used for word alignment. It shifts the word by one bit.

Q0 to Q6

7 bits of output data.

Summary of Contents for ECP5 Versa























































































Search results

Summary of Contents for ECP5 Versa

Reviews:

Related manuals for ECP5 Versa

Brands by name

Popular brands

Lattice Semiconductor ECP5 Versa, Technical Note

Search results

Summary of Contents for ECP5 Versa

Reviews:

Related manuals for ECP5 Versa

Brands by name

Popular brands