Lattice Semiconductor ECP5 Versa Technical Note Download Page 20 | Manualshive

Page: 20 / 86

background image

ECP5 and ECP5-5G High-Speed I/O Interface

Technical Note

© 2014-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at

www.latticesemi.com/legal

All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.

20

FPGA-TN-02035-1.3

Interface Requirements



The clock input must use a dedicated PCLK input so that it can be routed directly to the DLLDEL module.



ECLK must use the Edge Clock tree and the SCLK out of the CLKDIVD must use the Primary Clock tree, software
errors out if these dedicated clock routes are not used.



USE PRIMARY preference may be assigned to the SCLK net.



You must set the timing preferences as indicated in the

Timing Analysis for High Speed DDR Interfaces

section.

5.5.

GDDRX2_RX.MIPI

Generic Receive DDR for MIPI interfaces using the X2 gearing with ECLK. Clock is coming in centered to the data.

This interface must be used for speeds above 400 MHz.

This DDR interface uses the following modules:



IMIPI element use to receive the MIPI data and clock



The HSSEL of the IMIPI is used to switch between the High speed and Low Speed modes.



The HSSEL of IMIPI should be driven by a soft IP.



When in high-speed mode



The OHSOLS1 of the element is active.



The OHSOLS1 of the data IMIPI element is connected to the data input GDDRX2_RX.ECLK.Centered Interface.



The OHSOLS1 of the clock IMIPI is connected to the ECLK input GDDRX2_RX.ECLK.Centered Interface.



This is then treated similar to the GDDRX2_RX.ECLK.Centered Interface.



When in low speed mode:



Both the outputs of IMIPI are active since it is not a 2-bit interface.



The OHSLS1 is the bit 1 and OLS0 is the bit 0 of the interface.



Each of the data input and clock input is connected through a 20 ns filter soft IP to the core.



The ECLKBRIDGE can be optionally enabled if the data bus is crossing over between the left and right sides of
the device. If ECLKBRIDGE is enabled, then the ECLKBRIDGECS element should be used in the interface before
the ECLKSYNCB element. This element can be enabled through Clarity Designer.

Figure 5.9. GDDRX2_RX.MIPI

Interface Requirements



The clock input must use a PCLK input so that it can be routed directly to the Edge Clock tree.



ECLK must use the Edge Clock tree and the SCLK out of the CLKDIVF must use the Primary Clock tree, software
errors out if these dedicated clock routes are not used.



USE PRIMARY preference may be assigned to the SCLK net.



You must set the timing preferences as per section as indicated in the

Timing Analysis for High Speed DDR

Interfaces

section.

«
...
18
19
20
21
22
...
»

Summary of Contents for ECP5 Versa























































































Reviews:

No comments

Related manuals for ECP5 Versa

Brand: Pall Pages: 51

Brand: ZAMST Pages: 21

Brand: Datavideo Pages: 50

Brand: Waterous Pages: 90

Brand: Campbell Pages: 14

Brand: Dairyland Pages: 21

Brand: Abbott Pages: 2

FreeStyle Libre

Brand: Abbott Pages: 3

Brand: abc Pages: 8

Brand: Tascam Pages: 8

Brand: B-K lighting Pages: 5

Brand: B-K lighting Pages: 4

Brand: B-K lighting Pages: 3

Brand: ParaBody Pages: 5

Brand: HALDER Pages: 2

Brand: Hakko Electronics Pages: 16

Brand: Fenton Pages: 16

Life/form SmartScope LF01142U

Brand: Nasco Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands