Lattice Semiconductor ECP5 Versa Technical Note Download Page 55 | Manualshive

Page: 55 / 86

background image

ECP5 and ECP5-5G High-Speed I/O Interface

Technical Note

© 2014-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at

www.latticesemi.com/legal

All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.

FPGA-TN-02035-1.3

55

Table 7.3. DDR_Generic Configuration Tab Parameters

User Interface Option

Description

Values

Default

Interface selection based
on pre-configuration

Indicates interface is selected based on
selection made in the Pre-configuration
tab. Disabling this checkbox allows you to
make changes if needed.

ENABLED, DISABLED

ENABLED

Interface Type

Type of Interface (Transmit or Receive)

Transmit, Receive, Receive MIPI

Receive

Enable Tristate Control

Generate Tristate control for Transmit
Interfaces

ENABLED, DISABLED

DISABLED

I/O Standard

I/O Standard used for the interface

All Legal Input and Output
standards

LVCMOS25

Clock Frequency

Speed of the Interface

100 MHz–400 MHz (Transmit)
3.125 MHz–400 MHz (Receive)
200 MHz–400 MHz (Receive MIPI)

200 MHz

Gearing Ratio

DDR register gearing ratio

2:1, 4:1

2:1

Alignment

Clock to data alignment

Edge-to-Edge or Centered

Centered

Bus Width

Bus width for each interface

1–256

10

Organize Parallel Data

Allows you to select how the data bits of
the parallel bus should be arranged. You
can choose to set it By Lane where all the
parallel data bits from each lane are
organized together in the data output. If

By Time

is chosen instead, a single bit

from each of the data lanes is put
together in the data output.

By Lane, By Time

By Time

Enable ECLK Bridge
(required if bus is
crossing sides)

This is required if the data bus is wide and
is crossing sides.
Enabling this option instantiates the ECLK
Bridge module in the HDL.

Enable, Disable

Disable

Interface

Shows list of all valid high-speed
Interfaces for the given configuration.

to see the

interfaces available for a given
configuration.

—

Data Path Delay

Data input can be optionally delayed using
the DELAY block. Default Value is selected
based on Interface Type.

If Interface Type = Receive:
Static Default
Dynamic Default
Static User-Defined
Dynamic User-Defined
If interface type = Receive MIPI
Static Default
Static User-Defined
If Interface Type = Transmit:
Bypass
Static User-Defined
Dynamic User-Defined

If Interface Type

= Receive:

Static Default

If Interface Type

= Transmit:

Bypass

Delay Value for User-
Defined

When Data Path Delay of user-defined is
selected, you also need to set the number
of delay steps to be used.

1–127

1

Enable Dynamic Margin
Control on Clock Delay

Allows dynamic user control on clock
phase shift for Receiver edge to edge
aligned interfaces.

Enable, Disable

Disable

Generate PLL with this
module

When is option is enabled for Transmit
interfaces, the PLL used to generate the
clocks is included in the generated
module.

Enable, Disable

Disable

PLL Input Clock
Frequency

Frequency of the clock used as PLL Input

10 MHz–400 MHz

—

«
...
53
54
55
56
57
...
»

Summary of Contents for ECP5 Versa























































































Reviews:

No comments

Related manuals for ECP5 Versa

Brand: Daavlin Pages: 13

Brand: Daavlin Pages: 27

Brand: GALLERY Pages: 18

Infield Rascal Pro

Brand: ABI Attachments Pages: 8

Brand: Abicor Binzel Pages: 84

Brand: ABI Attachments Pages: 5

Brand: abem Pages: 47

Brand: Abely Pages: 5

Brand: xsto Pages: 76

Brand: F&V Pages: 5

Brand: F Care Systems Pages: 2

Brand: Nektar Pages: 12

ABS-Lock III-BE

Brand: ABS Pages: 8

Brand: Cablexpert Pages: 12

Maestro SB-CO-DIV-008B

Brand: Pentair Pages: 52

Brand: Grundfos Pages: 43

Z62-M450.01 S21

Brand: Jäger Pages: 36

Brand: Denon Pages: 119

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands