Lattice Semiconductor ECP5 Versa Technical Note Download Page 32

Page: 32 / 86

ECP5 and ECP5-5G High-Speed I/O Interface

Technical Note

www.latticesemi.com/legal

All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.

FPGA-TN-02035-1.3

FPGA

(DDR Memory Controller)

DQ[7:0]

DQS/DQS#

CA[9:0]

CSN, CKE

ODT(LPDDR3)

CK/CK#

DDR Memory

DQ[7:0]

DQS/DQS#

CA[9:0]

CSN, CKE

ODT(LPDDR3)

CK/CK#

DQ[7:0]

DQS/DQS#

CA[9:0]

CSN, CKE

ODT

CK/CK#

Figure 6.2. Typical LPDDR2/LPDDR3 Memory Interface

DQS(at PIN)

DQ(at PIN)

DQS(at IDDR)

DQ(at IDDR)

90 degree phase shift between DQS pin to IDDR

Preamble

Postamble

Figure 6.3. DQ-DQS During Read

DDR 1 / DDR 2

DDR 3

DQS(at PIN)

DQ(at PIN)

DQS(at PIN)

DQ(at PIN)

Figure 6.4. DQ-DQS During Write

Table 6.1

shows the different DDR memory configurations and features supported by ECP5 and ECP5-5G device.

Summary of Contents for ECP5 Versa























































































Search results

Summary of Contents for ECP5 Versa

Reviews:

Related manuals for ECP5 Versa

Brands by name

Popular brands

Lattice Semiconductor ECP5 Versa, Technical Note

Search results

Summary of Contents for ECP5 Versa

Reviews:

Related manuals for ECP5 Versa

Brands by name

Popular brands