Lantronix MSS Reference Manual Download | Manualshive

Page: 53 / 93

background image

Command Reference

Change Secondary

2-43

TXDrive

Controls how the MSS drives the TX pin.

Always

Sets the MSS to drive TX. The MSS will never tristate TX, even if data is not
being sent.

Auto

Sets the MSS to drive TX only when transmitting, and tristate when not
transmitting.

Defaults

Disabled
Mode = 4Wire
Termination disabled
TXDrive = Always

2.52 Change Secondary

Users can configure a secondary gateway, loadhost, and/or nameserver in case the primaries are
unreachable. For information, please see the Change Gateway (page 2-24), Change Loadhost (page 2-29),
and Change Nameserver (page 2-33) command entries.

2.53 Change Session Limit

Sets a server-wide limit for active sessions per port.

Restrictions

Requires privileged user status.

Parameters

Server

MSS4 only.

number

Enter a value between 0 and 8.

Defaults

4

2.54 Change Signal Check

Determines whether the MSS will check for the DSR signal when connections are made from the network
to a serial port. If the DSR signal is not present, the connection will be rejected.

CHANGE SERVER SESSION LIMIT

number

CHANGE PORT PortList SIGNAL CHECK

DISABLED

ENABLED













«
...
51
52
53
54
55
...
»

Summary of Contents for MSS






























































































Reviews:

No comments

Related manuals for MSS

Brand: IBM Pages: 40

Brand: Far south networks Pages: 4

AMD Opteron LS20 Type 8850

Brand: IBM Pages: 68

Brand: Inspur Pages: 82

Brand: Acer Pages: 52

Brand: Acer Pages: 94

Altos R700 Series

Brand: Acer Pages: 135

Brand: Acer Pages: 10

Brand: Acer Pages: 148

Brand: Acer Pages: 108

Brand: Acer Pages: 118

Brand: Acer Pages: 78

Altos G700 series

Brand: Acer Pages: 126

Altos S700 Series

Brand: Acer Pages: 124

Brand: Acer Pages: 126

Altos G320 Series

Brand: Acer Pages: 132

AcerAltos 21000

Brand: Acer Pages: 147

Altos 19000PRO4

Brand: Acer Pages: 157

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands