Lantronix MSS Reference Manual Download

Page: 74 / 93

Show Hostlist

Command Reference

2-64

2.87 Show Hostlist

Displays the current list of remote hosts to use for multihost mode connections.

See Also

Status Displays, page 7-6; Multihost Mode, page 7-10; Hostlist, page 2-58.

2.88 Show IPsecurity

Displays the current TCP/IP security table. Each address or range is shown, along with the direction of
concern.

See Also

Status Displays, page 7-6.

2.89 Show NetWare

Displays NetWare characteristics, including frame types, routing status, and internal network number.

Errors

Does not apply to MSSLite, MSS-VIA, or the MSS4.

See Also

Status Displays, page 7-6.

2.90 Show Nodes

Displays information about the desired LAT or SPX service nodes.

Errors

All nodes will be shown if no node is specified.

Does not apply to the MSS-Via, MSS4, or MSSLite.

Parameters

LAT

Shows LAT nodes identification strings and availability.

SHOW HOSTLIST

SHOW IPSECURITY

SHOW NETWARE

SHOW NODES

LAT

SPX













Summary of Contents for MSS






























































































Search results

Summary of Contents for MSS

Reviews:

Related manuals for MSS

Brands by name

Popular brands

Lantronix MSS, Reference Manual

Search results

Summary of Contents for MSS

Reviews:

Related manuals for MSS

Brands by name

Popular brands