manualshive.com logo in svg

Lantronix MSS, Reference Manual, Page: 45 / 93

Share
Download
Lantronix MSS Reference Manual Download Page 45

Command Reference

Change NetWare Routing

2-35

Parameters

fileserver

Enter the name of the desired fileserver using no more than 8 characters.

None

Specifies that no loadhost will be used. 

See Also

Change Software, page 2-45.

2.39   Change NetWare Routing

Allows the MSS to act as an internal router whenever there are multiple NetWare frame types in use on the 
LAN. 

Restrictions

Requires privileged user status.

The MSSLite, MSS4, and the MSS-VIA do not support Netware.

Defaults

Enabled

See Also

Change NetWare Encapsulation, page 2-33; Change NetWare Internal 
Network, page 2-34; Show NetWare, page 2-64.

2.40   Change Parity

Sets the parity for the specified serial port.

Restrictions

Requires privileged user status.

Errors

Parity must be None for the MSS100 and MSS-VIA to use 8-bit characters.

Autobaud will not work unless the port is using 8 bit characters with No parity 
or 7 bit characters with Even parity.

 CHANGE NETWARE ROUTING 

DISABLED

ENABLED

CHANGE  PORT   PortList   PARITY  

EVEN

MARK

NONE

ODD

SPACE

Summary of Contents for MSS






























































































Reviews:

No comments