Lantronix MSS Reference Manual Download

Page: 43 / 93

Command Reference

Change Nameserver

2-33

Errors

The server name must be unique to the network.

Parameters

Server

MSS4 only.

serverName

Enter a string of up to 16 characters. Strings must be enclosed in quotes if they
contain lower-case letters, spaces, or punctuation.

See Also

Change WINS, page 2-51.

2.35 Change Nameserver

Specifies the nameserver to be used during TCP/IP connections. The nameserver will attempt to resolve text
host names into numeric IP address form.

Restrictions

Requires privileged user status.

Parameters

Server

MSS4 only.

Secondary

Specifies a nameserver to be used when the primary nameserver is unavailable.

IPaddress

Specify a host using standard numeric format. Do not enter a text host name.

2.36 Change NetWare Encapsulation

Configures the frame types that the MSS will pay attention to during IPX connections. When NetWare
routing is enabled with the Change NetWare Routing command, all frame types are enabled regardless of
the settings made with this command.

Restrictions

Requires privileged user status.

The MSSLite, MSS4, and the MSS-VIA do not support Netware.

Errors

When enabling more than one frame type, you must enable NetWare Routing.

CHANGE SERVER SECONDARY NAMESERVER

IPaddress

CHANGE NETWARE ENCAPSULATION

ETHER_II

NATIVE

SNAP

802_2

















DISABLED

ENABLED













Summary of Contents for MSS






























































































Search results

Summary of Contents for MSS

Reviews:

Related manuals for MSS

Brands by name

Popular brands

Lantronix MSS, Reference Manual

Search results

Summary of Contents for MSS

Reviews:

Related manuals for MSS

Brands by name

Popular brands