Lantronix MSS Reference Manual Download

Page: 44 / 93

Change NetWare Internal Network

Command Reference

2-34

Parameters

Ether_II

Enables Ethernet v2 frame type.

Native

Enables the “native mode” NetWare frame type.

Snap

Enables the 802.2 frame type with SNAP SAPs.

802_2

Enables the 802.2 frame type with NetWare SAPs.

Defaults

all Enabled (Internal routing also enabled)

See Also

Change NetWare Internal Network, page 2-34; Change NetWare Routing,
page 2-35; Show NetWare, page 2-64.

2.37 Change NetWare Internal Network

Changes the MSS’s preset internal network number, which is derived from the unit’s Ethernet address. This
number is used for internal NetWare routing.

Restrictions

Requires privileged user status.

The MSSLite, MSS4, and the MSS-VIA do not support Netware.

Parameters

number

Specify the new internal network number in the format annnnnnn where a
represents a letter and each n represents a number.

See Also

Change NetWare Encapsulation, page 2-33; Change NetWare Routing, page
2-35; Show NetWare, page 2-64.

2.38 Change NetWare Loadhost

Specifies the name of the fileserver from which download attempts will be made at boot time.

Restrictions

Requires privileged user status.

The MSSLite, MSS4, and the MSS-VIA do not support Netware.

CHANGE NETWARE INTERNAL NETWORK

number

CHANGE NETWARE LOADHOST

fileserver

NONE

Summary of Contents for MSS






























































































Search results

Summary of Contents for MSS

Reviews:

Related manuals for MSS

Brands by name

Popular brands

Lantronix MSS, Reference Manual

Search results

Summary of Contents for MSS

Reviews:

Related manuals for MSS

Brands by name

Popular brands