Lantronix MSS Reference Manual Download

Page: 31 / 93

Command Reference

Change DHCP

2-21

2.14 Change DHCP

Enables or disables querying for a DHCP host at system boot time.

Restrictions

Requires privileged user status.

Errors

Configuring an IP address will automatically disable DHCP.

Enabling DHCP will remove the IP address saved in non-volatile memory
(NVR).

Parameters

Server

MSS4 only.

Defaults

Enabled

See Also

The IP Address Configuration section of your Installation Guide.

2.15 Change Domain

Specifies the default domain name to be used when attempting to resolve text TCP/IP host names.

Restrictions

Requires privileged user status.

Parameters

Server

MSS4 only.

DomainName

Enter a domain name of no more than 64 characters.

None

Disables the previously configured domain name.

See Also

Change Nameserver, page 2-33

CHANGE SERVER DHCP

DISABLED

ENABLED













CHANGE SERVER DOMAIN

DomainName

NONE













Summary of Contents for MSS






























































































Search results

Summary of Contents for MSS

Reviews:

Related manuals for MSS

Brands by name

Popular brands

Lantronix MSS, Reference Manual

Search results

Summary of Contents for MSS

Reviews:

Related manuals for MSS

Brands by name

Popular brands