manualshive.com logo in svg

Lantronix Maestro E205XT02, User Manual, Page: 30 / 213

Share
Download
Lantronix Maestro E205XT02 User Manual Download Page 30

 

 

Status 

E220 Series Cellular Router User Guide 

 

30 

I. 

Associated Stations 

Status > Overview > Status 

The Associated Stations group enlists the computers and/or devices that are connected to the router 
over Wi-Fi.  
 

Note 

•

 

Associated Station details are available only when router is configured as Master 
(access point). 

 
 

 

Screen 8-1I: Associated Stations Status Overview 

 

Parameters 

Description 

Associated Stations

 

MAC Address

 

MAC Address of the computers and/or devices that are connected to 
the router. 

Network 

Mode and Name of the network to which the device is connected. 

Signal 

Signal strength in dBm  

Noise 

Noise in dBm 

RX Rate 

Data transfer rate at which the data is received.  

TX Rate 

Data transfer rate at which the data is transmitted.  

•

 

Modulation and Coding Scheme (MCS) 1,  

•

 

High Throughput (HT) 20 Mhz 

Table 8.1-I: Associated Stations Status Overview  

 

 

Summary of Contents for Maestro E205XT02






















































































































































































































Reviews:

No comments