manualshive.com logo in svg

Lantronix Maestro E205XT02, User Manual, Page: 22 / 213

Share
Download
Lantronix Maestro E205XT02 User Manual Download Page 22

 

 

Status 

E220 Series Cellular Router User Guide 

 

22 

B.  Cellular 

Status > Overview > Status  

The Cellular group provides the status of the SIM card inserted in the router. 
 

 

Screen 8-1B: Cellular Status Overview 

 

Parameters 

Description 

Cellular Data

 

Displays the status of the Cellular data. 

 

Status 

•

 

ERROR  –

  SIM Card is not available in the Router or 

cellular connectivity malfunction. 

•

 

Connected –

 SIM card is active, and is connected for data 

communication.   

•

 

Disconnected –

 SIM card is inactive and there is no data 

communication. 

Signal Strength 

Displays the current signal strength.  

The signal strength range is 0 to 32.  

•

 

0 –

113 dBm or less 

•

 

1 –

111 dBm 

•

 

2 to 30

 

–

109 to –53 dBm 

•

 

31 – 

51dBm or greater 

 

Note 

•

 

Signal strength for a good cellular data connection must be 
12 or above. 

SIM Status 

Displays the availability of SIM card in SIM card slot. 

•

 

Error – 

SIM card is not inserted.

 

•

 

Ready – 

SIM card is inserted. 

Network Status 

The registration status of the router on the current cellular network. 

Operator Name 

Name of the current cellular operator in use. 

Roaming Status 

The roaming status of the router: 

•

 

Home  

•

 

Roaming  

IMSI 

Displays the IMSI Number. In case of UMTS, it is read from the SIM 

Summary of Contents for Maestro E205XT02






















































































































































































































Reviews:

No comments