manualshive.com logo in svg

Lantronix Maestro E205XT02, User Manual, Page: 176 / 213

Share
Download
Lantronix Maestro E205XT02 User Manual Download Page 176

 

 

Services 

E220 Series Cellular Router User Guide 

 

176 

  GRE 

 
 
The E2xx series router supports GRE. GRE is not a part of the base firmware package and needs to 
be downloaded from D2Sphere.  
 
For more information on how to download, please refer to section 

10.3 - Softwares

 

 

 

 

 

Parameters 

Description 

Interface Overview

 

Profile Name 

Displays the all the configured GRE Interfaces. The pre-configured 
interfaces for the router are 

•

 

GRE1 

Status

 

Displays the following Interface details: 

•

 

RX  

•

 

TX   

Actions 

Select the action to be taken for the Interface. 

•

 

Connect  –

  Connects the interface or reconnects the 

already connected interface 

•

 

Stop –

 Stops the Interface 

•

 

Edit –

 Click to edit the Interface. 

•

 

Delete –

 Click to delete the Interface. 

 

 

 

Summary of Contents for Maestro E205XT02






















































































































































































































Reviews:

No comments