manualshive.com logo in svg

Lantronix Maestro E205XT02, User Manual, Page: 150 / 213

Share
Download
Lantronix Maestro E205XT02 User Manual Download Page 150

 

 

Network 

E220 Series Cellular Router User Guide 

 

150 

b.  Advanced Settings 

 

 

Screen 10-57: Advance Configuration for Firewall Zone (LAN) 

 

Parameters 

Description 

Restrict to address family 

Select IP Address family for configuring firewall for LAN zone from 
available options. 

 

Available Options 

•

 

IPv4 

•

 

IPv6 

•

 

IPv4 and IPv6 

Restrict Masquerading to 
given source subnets 

Enter the source subnet to which the masquerading must be 
restricted. 

Restricts Masquerading to 
given destination subnets 

Enter the destination subnet to which the masquerading must be 
restricted. 

Force connection tracking 

Check to enable tracking of inbound connection to the router.  

Enable logging on this zone 

Check to enable logging of all the activities on the Zone. 

Table 10.9-3: Advance Configuration for Firewall Zone (LAN) 

 

 

Summary of Contents for Maestro E205XT02






















































































































































































































Reviews:

No comments