manualshive.com logo in svg

Lantronix Maestro E205XT02, User Manual, Page: 180 / 213

Share
Download
Lantronix Maestro E205XT02 User Manual Download Page 180

 

 

Services 

E220 Series Cellular Router User Guide 

 

180 

Parameters 

Description 

Verb 

Select the output verbosity level. Higher the verbosity, higher will be 
the internal log details. 

Port 

Enter the TCP/UDP port number for local and remote 

Tun_ipv6 

Enable the tunnel to handle IPv6 Traffic 

Server 

Enter the IP Address and Subnet Mask for server mode 

Nobind 

Check to enable Nobind. Enabling Nobind, does not allow the 
binding of local address and port.  

Comp_lzo 

Select Yes to use fast lzo compression. 

Keepalive 

Server sends the keep alive packets to clients  

Proto 

Select the protocol TCP and UDP. 

Client 

Check to enable the OpenVPN client mode and disable the 
OpenVPN server mode.  

Note  

•

 

Only OpenVPN Client mode is supported in Router Firmware 
Version Lantronix E205 2.0.0 and Lantronix E206 2.0.0 

client_to_client 

Check to facilitate communication between the Clients connected 
over the same VPN. 

Table 11.1-4: OpenVPN Service Configuration 

  Agents 

Services > Agents 

Agents are customized applications loaded on the router that are basically used for communication with 
a specific device/data management platform. 
 
By default, Lantronix  Wireless Automation Server (MWAS) agent is loaded on the router, which 
facilitates bi-directional data communication between Routers on the field (mainly using dynamic IP 
Address SIM cards) and a MWAS Server located centrally, communicating with the head-end system. 

 

Summary of Contents for Maestro E205XT02






















































































































































































































Reviews:

No comments