manualshive.com logo in svg

Lantronix Maestro E205XT02, User Manual, Page: 134 / 213

Share
Download
Lantronix Maestro E205XT02 User Manual Download Page 134

 

 

Network 

E220 Series Cellular Router User Guide 

 

134 

c.  MAC-Filter (Only for Interface configuration mode selected as Access Point) 

 

 

Screen 10-47: MAC Filter Configurations for a New Interface 

 

Parameters 

Description 

MAC-Address Filter 

MAC Address Filter is use to configure the white-listed or the black-
listed MAC Address.  

 

Available Options 

•

 

Disable 

•

 

Allow listed only

  –  Click 

  to add the allowed MAC 

Address.  

•

 

Allow all except listed

 – Click 

 to add the allowed MAC 

Address.  

 

By default the MAC-Address Filter is disabled. 

Table 10.3-6: MAC Filter Configurations for a New Interface 

 

Concept of Wi-Fi in E Series 

E Series treats Wi-Fi as an interface. By default there is on pre-created interface for Wi-Fi in 
access point mode. You can create multiple interfaces at the same time and assign multiple 
SSIDs to them.  
However while creating multiple interfaces for Wi-Fi please make sure that you do not create 
a few in Hotspot mode and few in client mode. 

 
 
 

 

 

Summary of Contents for Maestro E205XT02






















































































































































































































Reviews:

No comments