manualshive.com logo in svg

Lantronix Maestro E205XT02, User Manual, Page: 25 / 213

Share
Download
Lantronix Maestro E205XT02 User Manual Download Page 25

 

 

Status 

E220 Series Cellular Router User Guide 

 

25 

D.  Network 

Status > Overview > Status 

The Network group provides the status of IPv4and IPv6 WAN status 
 

 

Screen 8-1D: Network Status Overview 

 

Parameters 

Description 

WAN

 

Displays status of fixed-line WAN connection with following details: 

  

•

 

IP –

 IP Address of the WAN Interface. 

•

 

Gateway –

 IP Address of the WAN Interface Gateway. 

•

 

DNS  –

  Two  DNS IP Address; Primary DNS Server and 

Secondary DNS Server. 

 

Note 

•

 

In case of WAN Access Wi-Fi must be configured in client 
mode and connected to an Access Point. 

Cellular 

Displays status of Cellular network data connection with following 
details: 

  

•

 

IP –

 IP Address of the Cellular Interface. 

•

 

Gateway –

 IP Address of the Cellular Interface Gateway. 

•

 

DNS  –

  Two DNS IP Address; Primary DNS Server and 

Secondary DNS Server. 

WWAN 

Displays status of Wi-Fi WWAN connection with following details: 

  

•

 

IP –

 IP Address of the WWAN Interface. 

•

 

Gateway –

 IP Address of the WWAN Interface Gateway. 

•

 

DNS  –

  Two DNS IP Address; Primary DNS Server and 

Secondary DNS Server. 

 

Table 8.1-D: Network Status Overview 

 

 

Summary of Contents for Maestro E205XT02






















































































































































































































Reviews:

No comments