manualshive.com logo in svg

Lantronix Maestro E205XT02, User Manual, Page: 183 / 213

Share
Download
Lantronix Maestro E205XT02 User Manual Download Page 183

 

 

Services 

E220 Series Cellular Router User Guide 

 

183 

Parameters 

Description 

SMS Configuration  

SMS Administrator 

Displays the number of Administrators configured to receive the 
diagnostics information of the router after they send the command 
using SMS. 

  

Maximum 4 SMS Administrator can be configured. 

 

Note 

•

 

If no number is configured than the router will accept SMS 
from any number. 

Mobile Number 

Enter the mobile number. 

 

The format of mobile number must be: 

•

 

<countrycode><phonenumber> 

E.g. 919876543210 

Note 

•

 

The phone number must not include a special character 
“plus (+)” preceding it. 

If no number is configured than the router will accept SMS from any 
number. 

List of Commands 

Command name 

Command  

AT+REBOOT=1 

Reboot: reboot the modem 

AT+CELLDIAG? 

Cell diagnostics: will give you IMEI, CREG, COP, CSIG 

AT+LANDIAG? 

LAN diagnostics: Will give LAN IP address, 

AT+WANDIAG? 

Wired WAN diagnostics: 

AT+WANPING=<IPA> 

Wired WAN ping: will ping the wired WAN interface 

AT+LANPING=<IPA> 

LAN ping: will ping the wired LAN interface 

AT+REMACC=<1/0> 

Remote access: will enable; AT+REMACC=<1> or disable 
AT+REMACC=<0> remote access  

AT+HWI? 

Hardware information: will give you hardware information such as 
model number 

AT+SWI? 

Software information: will give you software information such as 
firmware version 

Table 11.3-1: SMS Service Configurations 

 

 

 

Summary of Contents for Maestro E205XT02






















































































































































































































Reviews:

No comments