Lantronix EPS Reference Manual Download Page 83 | Manualshive

Page: 83 / 223

background image

NetWare Host Setup

Printing

8-3

Pserver can also be configured manually via PCONSOLE on the file server(s). PCONSOLE is useful, for
example, when you want to see exactly what is being configured by the QINST utility. Some basic
familiarity with PCONSOLE is assumed in the examples.

Rprinter is set up via the PCONSOLE utility on the file server(s). Again, basic familiarity with PCONSOLE
is assumed in the examples.

8.3.1 Creating NDS Print Queues with PCONSOLE

The Quick Setup option is the easiest way to create NDS print queues with PCONSOLE. The following
steps refer to NetWare v4.x or greater.

License NDS on your Server as explained in the Licensing NDS section on page 8-1.

1

Configure the Server.

A

Use the Set/Define Protocols NetWare DSTree command to define the directory service tree in
which the print server is located.

Figure 8-3: Defining the Directory Service Tree

Note:

For an explanation of the structure of the NetWare Directory Service tree, see
your host documentation.

B

Use the Set/Define Protocols NetWare DSContext command to define the directory service
context where the print server is located.

Figure 8-4: Defining the Directory Service Context

C

Enter the List Protocol NetWare Access command to ensure that at least one of the file servers
in the directory service tree is in the access list.

The access list is set to Local by default, which includes all file servers attached to a local Ethernet
segment (not accessed through a router). To add to this list, enter the Set/Define Protocols Net-
Ware Access command.

Figure 8-5: Adding to the Access List

2

Reboot the Server.

Figure 8-6: Rebooting the Server

3

Set up the PCONSOLE print queue.

Local>> DEFINE PROTOCOL NETWARE DSTREE foodco

Local>> DEFINE PROTOCOL NETWARE DSCONTEXT

ou=kiwi.ou=exotic.o=fruit

Local>> DEFINE PROTOCOL NETWARE ACCESS

fileserver

Local>> INIT DELAY 0

«
...
81
82
83
84
85
...
»

Summary of Contents for EPS
































































































































































































































Reviews:

No comments

Related manuals for EPS

CLP-680ND: CLP-775ND

Brand: Samsung Pages: 2

Brand: 360 Systems Pages: 117

Brand: TallyGenicom Pages: 166

Brand: idp Pages: 104

Brand: Oki Pages: 180

Brand: Tally Pages: 266

Brand: AXIOMTEK Pages: 58

xPort Pro XPP1004000-02R

Brand: Lantronix Pages: 17

Brand: SPRT Pages: 21

eServer BladeCenter HS20Type 8832

Brand: IBM Pages: 112

Brand: Oki Pages: 309

Brand: NEC Pages: 10

LabeLase 1000Exhaust

Brand: InfoSight Pages: 38

eServer xSeries 335 Type 8676

Brand: IBM Pages: 178

Brand: Infinite Peripherals Pages: 29

Brand: WOOSIM Pages: 24

Brand: Panasonic Pages: 17

Brand: Panasonic Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands