manualshive.com logo in svg

Lantronix EPS, Reference Manual

Share
Download
Lantronix EPS Reference Manual Download Page 11

1-1

1:  Introduction

1.1   Product Overview

The Lantronix Print Servers (EPS, MPS, and LPS models) are multi-protocol print servers that provide 
shared network access to printers for a variety of network protocols and operating systems. The print servers 
generally support the TCP/IP, IPX (NetWare), and Local Area Transport (LAT), AppleTalk (EtherTalk), 
and Microsoft LAN Manager protocols. They can queue multiple pending jobs and service those jobs in the 
order in which they are received from hosts. 

Note:

The LPS does not support AppleTalk or LAT.

For a description of your individual print server model, please refer to the Installation Guide that came with 
your print server.

Lantronix servers store their executable software in Flash (rewritable) ROM, meaning that they do not have 
to download software from a host each time they boot. Software must only be downloaded when a new 
software version becomes available. See Appendix D for more information.

Note:

In this manual, all servers will be referred to as “the Server” unless a distinction 
needs to be made between models. 

1.2   Protocol Support

The Server supports five industry-standard network protocols:

TCP/IP

TCP/IP is a widely-used protocol that can be run on networks with Macintoshes, PCs, and Unix 
workstations. Server support includes Telnet, Rlogin, and the LPR and RTEL printing systems.

NetWare (IPX/SPX )

NetWare allows devices attached to the Server to act as networked printers. The Server supports all 
NetWare frame types: Ethernet v2, Native Mode (802.3), 802.2, and 802.2 SNAP. In addition, it 
supports both Bindery mode and NetWare Directory Services (NDS). 

Local Area Transport (LAT)

LAT is a protocol developed by Digital Equipment Corporation for local network terminal connec-
tions and is supported on almost all Digital operating systems. It provides both logins to remote 
hosts and host-initiated print spooling.

AppleTalk

AppleTalk allows networked Apple Macintosh computers to see devices attached to the Server and 
access them as they would any networked printer. 

LAN Manager

The Server allows devices on LAN Manager networks to access networked printers. Systems run-
ning Windows NT can access the devices using the Digital Network Port for Windows NT or the 
NetBIOS protocol.

Summary of Contents for EPS
































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands