Lantronix 4120 Series User Manual Download

Page: 74 / 142

Lantronix

x4120 User Guide

33551 Rev. C

https://www.lantronix.com/

Page

142

Please change to power supply slot first before showing its configure!

You entered the show power config command from a device other than the power supply. For example:

C1|S16|L1D>

show power config

Please change to power supply slot first before showing its configure!

C1|S16|L1D>

1. Make sure this is the command you want.

2. Verify the command syntax.

3. Use the go command to switch to the slot containing the power supply (typically slot 22 and/or 23).
4. Contact Lantronix for more information.

IP management is not supported on this card!

No tdm loopback supported on this card!

Syslog is not supported on this card!

TAOS status setting is not supported on this card!

TNDP is not supported on this card!

You entered a command for a function that is not supported on the x4120. For example:

C1|S15|L1D>

set dhcp state disable

IP management is not supported on this card!

C1|S15|L1D>

1. Try another command on the x4120.

2. Try the command on another card that supports the attempted function.
3. If the problem persists, contact Technical Support.

Cannot set if this port can be managed by CPU on this card!

Cannot set USB port state on this card!

tftp get: set address type failed.

You entered a tftp command, but the address entered was not accepted.

C1|S15|L1D>

tftp get iptype ipv4 ipaddr 192.168.1.30 remotefile

x4120_1.0.4_AP

tftp get: set address type failed.

C1|S15|L1D>

1. Make sure the tftp server address is valid.
2. Verify that the TFTP Server is running and properly configured.

3. Try entering the tftp command again.
4. If the problem persists, contact Technical Support.

Summary of Contents for 4120 Series















































































































































Search results

Summary of Contents for 4120 Series

Reviews:

Related manuals for 4120 Series

Brands by name

Popular brands

Lantronix 4120 Series, User Manual

Search results

Summary of Contents for 4120 Series

Reviews:

Related manuals for 4120 Series

Brands by name

Popular brands