manualshive.com logo in svg

Lantronix 4120 Series, User Manual

Share
Download
Lantronix 4120 Series User Manual Download Page 115

Lantronix   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

          x4120 User Guide 

33551 Rev. C

 

https://www.lantronix.com/

 

Page 

115

 of 

142

 

ifconfig  

1.  Verify that the machine's interfaces are up and have an IP address using the 

ifconfig

 command:  

 

[root@sleipnir root]# ifconfig 

eth0      Link encap:Ethernet  HWaddr 00:0C:6E:0A:3D:26 

         inet addr:192.168.168.11  Bcast:192.168.168.255  Mask:255.255.255.0 

         UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1 

         RX packets:13647 errors:0 dropped:0 overruns:0 frame:0 

         TX packets:12020 errors:0 dropped:0 overruns:0 carrier:0 

         collisions:0 txqueuelen:100 

         RX bytes:7513605 (7.1 Mb)  TX bytes:1535512 (1.4 Mb) 

         Interrupt:10 

 

lo        Link encap:Local Loopback 

         inet addr:127.0.0.1  Mask:255.0.0.0 

         UP LOOPBACK RUNNING  MTU:16436  Metric:1 

         RX packets:8744 errors:0 dropped:0 overruns:0 frame:0 

         TX packets:8744 errors:0 dropped:0 overruns:0 carrier:0 

         collisions:0 txqueuelen:0 

         RX bytes:892258 (871.3 Kb)  TX bytes:892258 (871.3 Kb) 

 

The above machine is running normally. The first line of output shows that the Ethernet interface eth0 

has a layer 2 (MAC or hardware) address of 00:0C:6E:0A:3D:26. This confirms that the device driver 

is able to connect to the card, as it has read the Ethernet address burned into the network card's 

ROM. The next line shows that the interface has an IP address of 192.168.168.11, and the subnet 

mask and broadcast address are consistent with the machine being on network 192.168.168.0. 

Summary of Contents for 4120 Series















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands