background image

Lantronix   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

          x4120 User Guide 

33551 Rev. C

 

https://www.lantronix.com/

 

Page 

26

 of 

142

 

Circuit ID Config – Web Method 

1.  Access the x4120 via the Web interface (see 

“Starting the Web Interface” 

on page

 45

).  

2.  Select the appropriate port and locate the 

Circuit ID

 field.  

3.  Enter the Circuit ID of up to 64 bytes for the port. The default is blank.  

 

4.  Click 

Save

 to update screen information. 

5.  Repeat steps 2 -4 for each port as required.  
6.  Click 

Save

 when done.  

 

If you enter more than 64 characters for the Circuit ID and then click 

Save

, the characters entered display 

in red, and the message “

Invalid input found!

” displays in the lower left corner of the Web interface.  

To recover:  

c)  Click Refresh, and re-enter a Circuit ID of 64 or fewer characters and click 

Save

.  

d)  The message “

Setting values succeeded

” displays in the lower left corner of the Web interface.  

 

 

Summary of Contents for 4120 Series















































































































































Reviews: