3-8
9K713-0522
OPERATION
Brillion Elite Mini Monitor -
Optional
Brillion Elite Mini Monitor provides information to the
operator and acts as an interface for clutch control. The
display shows seed shaft rotation, low bin levels, acres
seeded, and clutch engagement. The touch screen allows
the operator to engage all or individual clutches.
IMPORTANT
The Brillion Elite Mini Monitor System by Loup
utilizes a MUX communication line. Sensors must be
learned into the Monitor. Location of each pre-learned
Smart Shaft Sensor or Bin Level Sensor is important
for proper Monitor display. Each Sensor utilizes 3
wires (+, -, MuxBus) to connect to the system. The
Harnesses do not require a specific Sensor
connection points. Each Sensor is identified in the
Monitor by its own signal.
WARNING
See "Brillion Elite Mini Monitor" Chapter
for more
information and a detailed guide to the use of your
monitor.
•
Bin Level Sensors are installed on adjustable
brackets in the outer ends of the seed box. When the
sensor is submerged in seed, no alarm will sound. As
the seed level falls below the sensor eye, an alarm
will be indicated on the Brillion Elite Mini Monitor.
Raise or lower the Bin Level Sensor Bracket inside
the Seed Box to the desired seed level.
•
On the RH side of the Seeder is a Smart Shaft
Sensor that is installed on a Sensor Mount that is
attached to the mounting hardware of two seed cups.
The Smart Shaft Sensor is activated by a High
Powered Magnet that is placed on the Seed Shaft
and is kept in place with a Collar. As the seed shaft
rotates the Smart Shaft Sensor detects the magnet.
When no signal is detected for pre-defined seconds,
an alarm will be indicated on the Brillion Elite Mini
Monitor.
NOTE
If shaft sensor stall alarm occurs, be aware that the
affected seeder has not been planting for pre-defined
seconds.
•
Brillion Elite Mini Monitor provides users the ability to
toggle the seeder clutch on or off.
•
Brillion Elite Mini Monitor will monitor field and total
acres.
•
Brillion Elite Mini Monitor is operated on a 12-Volt DC
negative ground system. The monitor should be
connected using the existing convenience plug
connection.
•
The Elite Mini Tractor Harness attaches to the Brillion
Elite Mini Monitor and connects to the Seeder 240"
Extension Harness.
The 6-Pin
Connection may be plugged/unplugged at the front of
the Seeder Hitch when hooking/unhooking the
Seeder. This allows the monitor to stay in the tractor
if so desired.
•
A 4-Pin radar connection is provided as an optional
connection for the speed sensor. The speed signal
may be determined by either the tractor radar or the
speed sensor located on the Seeder.
For service or setup questions contact Loup Electronics
Inc.
“Service And Technical Support” on Page 4-8.
Console w/Clutch Control -
Optional
(Used on models before the Brillion Elite Mini Monitor)
Basic Operation:
During normal operation the console LED for the seed
shaft will not be illuminated. The Shaft Sensor will be
activated by a magnet wheel installed on the Seed Shaft
being monitored. The Shaft Sensors are standard Loup
Shaft Sensors, set to 20 second delay timing. When no
signal is detected for 20 seconds by the sensor, the
corresponding LED in the Console will illuminate and the
audible alarm will sound indicating a fault. The alarm will
become silent after 30 seconds and will not sound again
until the Seed Shaft returns to a fully functional condition.
NOTE
If shaft sensor stall alarm occurs, be aware that the
affected seed box has not been planting for 20 seconds.
The Clutch Master toggle switch allows you to go from
"SEED"
to
"NO SEED"
Figure 3-9: Console w/Clutch Control
Summary of Contents for Brillion Alfalfa SS108
