Landoll Brillion Alfalfa SS108 Operator'S Manual Download Page 32

Page: 32 / 92

2-16

9K713-0522

ASSEMBLY

TABLE OF CONTENTS

Brillion Elite Mini Monitor -

Optional

Assembly instruction for models with Clutch.

The Brillion Elite Mini Monitor System by Loup
utilizes a MUX communication line. Sensors must be
learned into the Monitor. Location of each pre-learned
Smart Shaft Sensor or Bin Level Sensor is important
for proper Monitor display. Each Sensor utilizes 3
wires (+, -, MuxBus) to connect to the system. The
Harnesses do not require a specific Sensor
connection points. Each Sensor is identified in the
Monitor by its own signal.

WARNING

IMPORTANT

All Harnesses must be firmly attached to Machine
Frame members so they do not sag or become torn
loose by field debris.

Refer to Brillion Elite Mini Monitor Electrical Schematic.

See Figure 2-24.

1. Lay out the Seeder Harnesses on the front of the

Seeder ensuring that the Electric Clutch 2-Pin
Connector is on the left side.

2. Remove Seeder Clutch. Install Actuator Assembly

onto the Quill Shaft outer diameter, secure with
Actuator Assembly Set Screw. Reinstall Clutch.

See

Figure 2-25.

Install Pick-up Switch Bracket to the

Transmission Input Shaft Bearing Flangette Hardware.
Assemble Smart Shaft Sensor onto the Pick-Up Switch
Bracket with sensor provided hardware and #8-32
Flange Locknuts. Adjust the Smart Shaft Sensor so
that it is 1/8" Max away from the Actuator Assembly.

See Figure 2-21.

Connect Ground Speed Smart Shaft

Sensor to the Center Seeder Harness.

3. Front RH side Seed Box between the 1st and 2nd

Seed Meters, place 1-1/4 x 1/4 x 1/16 Magnet on the
Seed Shaft. Secure with Magnet Collar.

See

Figure 2-26.

Remove the 2nd and 3rd Seed Meter

front Round Head Machine Screws that mounts the
Seed Meter to the Seed Box and replace them with
1/4-20 x 3/4 Round Head Machine Screws. Install the
Sensor Mount on the 1/4-20 x 3/4 Machine Screws.
Secure with Flat Washers, Lock Washers and Nuts.
Install a Smart Shaft Sensor to the Sensor Mount with
sensor provided hardware and #8-32 Flange
Locknuts. Adjust the Smart Shaft Sensor so that it is
1/8" Max away from the Magnet Collar on the Seed
Shaft.

See Figure 2-23.

Connect the Smart Seed

Shaft Sensor to the Seeder Harness.

Figure 2-21: Ground Speed Sensor Detail

4. Unused Seeder Harness RH 3-Pin Connector needs

to be sealed with a 3-Pin Shroud and Cavity Plugs to
protect the Harness from the environment.

5. The Seeder RH and LH ends only, remove the .803

Knockouts in the Seed Box.

Do Not remove the

Knockouts in the Seed Boxes at the center of the
Seeder.

6. On the inside at either end of the Seed Box, install a

Bin Level Sensor Bracket with the Seed Box Mounting
3/8-16 Hardware.

See Figure 2-27.

Determine the

desired level for the alarm to be indicated on the
Brillion Elite Mini Monitor and assemble the Bin Level
Sensors to Bin Level Sensor Brackets with sensor
provided hardware and #8-32 Flange Locknuts. If
more adjustment is needed, the Bin Level Sensor
Brackets can also be raised or lowered to the desired
seed level. Install Cord Grips from the inside of the
Seed Box out and secure with supplied Locknut on
the outside of the Seed Box. To get the Sensor
Connector outside the Seed Box, feed the terminals
through the Cord Grip. Install the terminals into the
3-Pin Shroud labeled “A”, “B” and “C” as follows “A”
White, “B” Black, “C” Green.

See Figure 2-22.

Inside

the Seed Box, add enough slack to the Bin Level
Sensor Cord to allow for future adjustments of the
Sensor. Secure the Bin Level Cord by tightening the
Cord Grip Compression Nut. Connect both Bin Level
Sensors to the Seeder Harness.

Figure 2-22: Bin Level Sensor Wire Detail

High Power Magnet is use. See “High Power
Magnet” on Page 1-2.

1/8"

Max

Pick-up Switch

Bracket

Smart Shaft

Sensor

Actuator

Assembly

Clutch

Transmission