2-12
9K713-0522
ASSEMBLY
Warning Lamp Installation,
12FT
NOTE
12FT Drawbar model is shown, 3-PT models similar.
1. Place a Red Lamp at each end of the Light Bar and
insert the Red Lamp Cord into the Light Bar cutout.
Secure Red Lamp to Light Bar with 1/4-20 x 1-1/4
Bolts and Locknuts.
2. Attach longer Light Bracket to the Transmission
located on the left side of the Seeder, with 3/8-16 x
1-1/2 Bolts, Lock Washers and Nuts.
3. Attach Amber Lamp to the outside of the Light Bracket
with 1/4-20 x 1-1/4 Bolts and Locknuts.
4. On the right side of the Seeder, attach the shorter
Light Bracket to the Angle Bracket with 1/2-13 x 1-1/4
Bolts, Lock Washers and Nuts.
5. Attach an Amber Lamp to the upper portion of the
Light Bracket with 1/4-20 x 1-1/4 Bolts and Locknuts.
6. Attach the Flasher Control Module to the Module
Bracket with 1/4-20 x 1-1/2 Bolts and Locknuts.
IMPORTANT
Cords are marked Yellow Tape for Left and Green
Tape for Right.
7. Lay out the Lamp Harness along the Seeder Frame
Tube, Cords with Yellow Tape Left and Cords with
Green Tape Right. Connect the Harness to the
Flasher Control Module 6-Prong Connector.
8. Route the left and right cords along the front of the
Frame Tube. Route the 3-Prong Connector Cords into
the Light Bar vertical tube openings up to the Red
Lamps and connect. Continue routing the 2-Prong
Connector Cord along the front of the frame, up the
outer Light Bracket to the Amber Lamps and connect.
9. Lay out the 7-Pin Harness along the 3-PT Hitch or
Drawbar with the 4-Prong Connector towards Seeder.
3-PT Hitch, route the 4-Prong Connector Cord
through the Frame Loop to the Module. Drawbar,
route the 7-Pin Harness along the Drawbar, through
the Hose Support up to the Tractor. Connect 7-Pin
Harness 4-Prong Connector to the Flasher Control
Module.
10. Bundle and secure excess Cords to the Module
Bracket with Tie Wraps. Along the Seeder Frame,
secure Harness Cords with Tie Wraps to the frame
end plate slots, Slotted Tabs and Hydraulic Hoses.
Bundle and secure 7-Pin Harness to the Drawbar
Hydraulic Hoses or 3-PT Hitch Frame Slots allowing
enough Harness length to reach the Tractor Socket.
NOTE
If equipped with optional Electrical Clutch, install, route
and secure Electric Clutch Harness with the Warning
Lamp Harness.
IMPORTANT
All wires must be firmly attached to Machine Frame
members or Hydraulic Hoses so they do not sag or
become torn loose by field debris.
11. Attach the SMV sign to the SMV Mount located on the
center of the Light Bar with 5/16-18 x 1 Bolts, Flat
Washers, and Locknuts.
12. Attach the Connector Holder to the Drawbar Hose
Holder or 3-PT Hitch with 1/4-20 x 1 Bolts, Flat
Washers, and Locknuts.
NOTE
The 7-Pin Plug on the other end of the 7-Pin Harness
connects to the Tractor Socket when in use. When not in
use, it can be stored in the Connector Holder on the
Drawbar Hose Holder or 3-PT Hitch. Allow enough
harness length to reach Tractor Socket and roll or fold up
excess and secure to Drawbar Hydraulic Hoses or 3-PT
Hitch.
Figure 2-16: Flasher Control Module and Bracket
Module Bracket
Flasher Control Module
Locknut,1/4-20
Bolt,1/4-20 x 1-1/2
Summary of Contents for Brillion Alfalfa SS108
