Landoll Brillion Alfalfa SS108 Operator'S Manual Download Page 33

Page: 33 / 92

ASSEMBLY

9K713-0522

2-17

TABLE OF CONTENTS

7. Connect the 240" Extensions Harness to the Seeder

Harness. Route the 240" Extension Harness along
the Seeder Frame and down the Drawbar/3-PT Hitch
to the Tractor.

8. Install Brillion Elite Mini Monitor on Tractor.

See

“Brillion Elite Mini Monitor Tractor Installation -
Optional” on Page 2-20.

9. If not already installed, install Smart Clutch Relay into

Elite Mini Tractor Harness 3-Pin Connectors.

10. Connect the Elite Mini Tractor Harness 14-Pin

Connector to Brillion Elite Mini Monitor, 3-Pin Power
Plug to 12 Volt Tractor Convenience Outlet and 6-Pin
Connector to the 240" Extension Harness. 4-Pin
Connector is not used at this time.

11. Bundle and secure all Harnesses along the Seeder

Frame and Drawbar/3-PT Hitch with Tie Wraps.

12. Program Bin Level Sensors and Smart Shaft Sensors

if not already pre-programmed.

See

“Brillion Elite

Mini Monitor” on Page 4-1.

Figure 2-23: Seed Box Seed Shaft Detail

Sensor Mount

Smart Shaft

Sensor

Seed Shaft,

3/8 Square

Magnet

1-1/4 x 1/4 x 1/16

Magnet Collar

3/8 Sq Shaft

SECTION A-A

1/8" Max

Magnet

1-1/4 x 1/4 x 1/16

Magnet Collar

3/8 Sq Shaft

Sensor Mount

Smart

Shaft Sensor

Summary of Contents for Brillion Alfalfa SS108





























































































Search results

Summary of Contents for Brillion Alfalfa SS108

Reviews:

Related manuals for Brillion Alfalfa SS108

Brands by name

Popular brands

Landoll Brillion Alfalfa SS108, Operator'S Manual

Search results

Summary of Contents for Brillion Alfalfa SS108

Reviews:

Related manuals for Brillion Alfalfa SS108

Brands by name

Popular brands