Landis+Gyr E470 Series User Manual Download Page 56

Page: 56 / 69

Page 56 of 69

Issue: 1.8

Meter Displays

E470 Tokenless Smart Prepayment Meter

9.8.17 Export Energy Register

The export energy register displays the amount of energy measured in

reverse through the meter. The register will roll over to zero after 99999.99.

The export register will have the same 0,1 or 2 decimal place resolution as

the TOU energy registers.

Pence/

kWh

€

E X P

0 0 3 3 5 7 8

9.8.18 Total Credit Register

The Total Credit Register displays the total value of purchased credit. See

section 5.3.

The Total Credit Register is displayed to 2 dp (whole pence/cents) without

leading zero’s.

Pence/ kWh

€

T P A Y

2 1 0 5 0

9.9 Purchase Code Entry

To enable the entry of various codes including installation, credit purchase

etc, the meter will allow the user to enter such a code using the two push

buttons fitted to the front of the meter.

The code entry sequence will operate the same for all types of code entry.

The code entry facility is entered using the Display Cycle (blue) and

Emergency credit (orange) buttons by pressing and holding both buttons for

2 seconds. While in the code entry mode normal button operation is

disabled.

When the facility has been entered the display will change from its normal

operating mode to display shown below.

Pence/ kWh

€

C O D E

0 0 0 0

Summary of Contents for E470 Series






































































Search results

Summary of Contents for E470 Series

Reviews:

Related manuals for E470 Series

Brands by name

Popular brands

Landis+Gyr E470 Series, User Manual

Search results

Summary of Contents for E470 Series

Reviews:

Related manuals for E470 Series

Brands by name

Popular brands