Landis+Gyr E470 Series User Manual Download Page 24

Page: 24 / 69

Page 24 of 69

Issue: 1.8

Installation and Binding of External Devices

E470 Tokenless Smart Prepayment Meter

Data Item

Returned in1 Details

Arrears Register

Rate 1 kWh register

Rate 2 kWh register

Rate 3 kWh register

Rate 4 kWh register

Total kWh register

Export energy register

Meter Removal Code

Meter Exchange code

Meter Fitter Authorisation Code

Return Data – Following the installation process the meter will be sent a full

configuration set of operation data including tariffs etc, from the utilities

information system. Additionally the meter may be sent Present balance

data and Arrears data if the meter is a replacement meter subject to an

exchange process.

5.2 Decommissioning

Decommissioning of a meter is achieved by entering one of the two

decommissioning codes sent to the system at installation. NOTE: The

meter engineer would be instructed of the codes by use of the system.

The entry of the Decommissioning Codes is achieved using the using the

standard Purchase Code entry procedure - see display section. Once 6

digits have been entered the installer can offer the code to the meter by

pressing and holding both buttons for 2 seconds. If the code does not

match the either the removal code or exchange code held in memory, the

meter will show ‘Error’ and clear the entry. Lock out procedure will apply

according to the Purchase Code entry scheme.

5.2.1 Meter Exchange

When the meter exchange code is entered the meter will send a snapshot

of meter data to the system. The information will include:

Data Item

Returned in1 Details

Date and Time stamp

Electricity Meter Status flags2

Message ID

Message ID = EXCHANGE

MPAN/Customer #

Meter Serial Number

Credit Mode

Denotes credit or prepayment operating mode

Emergency credit flags

Denotes emergency credit taken or not

Present Balance Register

Arrears Register

Rate 1 kWh register

Rate 2 kWh register

Rate 3 kWh register

Summary of Contents for E470 Series






































































Search results

Summary of Contents for E470 Series

Reviews:

Related manuals for E470 Series

Brands by name

Popular brands

Landis+Gyr E470 Series, User Manual

Search results

Summary of Contents for E470 Series

Reviews:

Related manuals for E470 Series

Brands by name

Popular brands