background image

17

TROUBLE

CAUSE

REMEDY

4.4 Insufficient water flow.

A. Insufficient incoming supply water 

pressure.

B. Shutoff on mounting bloack not fully 
open.

C. Foreign debris in water flow control.

D. Foreign debris in water pump strainer

A. Verify incoming supply water pressure 
is a minimum of 25 PSI (0.172 MPA).

B. Open shutoff fully.

C. Remove water flow control from upper 

body and clean out any foreign material 
to ensure smooth free spool movement.
 
D. Remove water pump strainer and 
clean.

4.5 Insufficient syrup flow.

A. Insufficent CO

pressure to BIB pumps.

B. Out of CO

.

C. Shutoff on mounting block not fully 
open.

D. Foreign debris in syrup flow control.

E. Bad syrup pump.

A. Adjust CO

2

 pressure to 80 PSI (0.550 

MPA) [minimum 70 PSI (0.480 MPA)] for 
BIB pumps.
B. Replace CO

2

 tank/refill.

C. Open shutoff fully.

D. Remove syrup flow control form upper 

body and clean out any foreign material 
to ensure smooth free spool movement.

E. Replace BIB pump.

4.6 Erratic ratio.

A. Incoming water and/or syrup supply 

not at minimum flowing pressure.

B. Foreign debris in water and/or syrup 

flow controls.

A. Check pressure and adjust

B. Remove flow controls from upper body 

and clean out any foreign material to 
ensure smooth free spool movement.

4.7 No product dispensed

A. Water and syrup shutoffs on mounting 
block not fully open.
B. The key switch on an electric valve is 
in the OFF position.

C. Cup lever arm or ID panel actuator on 
electric valve is not actuating the switch.

D. Electric current not reaching valve.

E. Improper or inadequate water or syrup 
supply.

F. Transformer Failure

G. Bad valve solenoid(s)

A. Open shutoff fully.

B. Turn key switch to ON position.

C. Repair

D. Check electric current supplied to 
valve. If current is adequate, check 
solenoid coil and switch, and replace if 
necessary.

E. Remove valve from mounting block 
and open shutoffs slightly and check 

water and syrup flow. If no flow, check 

dispenser for freeze-up or other problems

F. Reset transformer circuit breaker. If 
breaker trips again check for pinched wire 
harness at backblocks

G. Replace Solenoid(s)

CONTINUED ON NEXT PAGE.....

Summary of Contents for Spartan


























Reviews: