background image

 

 

Table of contents

 

 

1.

 

Performance Parameters

 _________________________________________  3 

2.

 

Technical Specifications

 _________________________________________  4 

3.

 

Control Panel

  __________________________________________________  5 

4.

 

Preparation and Start-up

 _________________________________________  7 

5.

 

Control Mode & Clock Checking

 ___________________________________  8 

6.

 

Temperature Retaining Switch Setting

 ______________________________  8 

7.

 

Temperature, Speed, Timer Settings

  _______________________________  9 

8.

 

Date & Time Settings

 ___________________________________________  10 

9.

 

Temperature & Speed Alarm Settings

  _____________________________  11 

10.

 

Refrigeration & Defrost Settings

 ________________________________  12 

11.

 

Temperature Calibration

 _______________________________________  14 

12.

 

Non-volatile memory function Setting

____________________________  15 

13.

 

Setting of communication address for RS485 connection (Opt)

  ______  15 

14.

 

Sum Run Time Checking

  ______________________________________  16 

15.

 

Operation and Switch off

 ______________________________________  16 

16.

 

Shaking Diameter Adjustment

 __________________________________  17 

17.

 

Trouble Shootings

  ___________________________________________  18 

18.

 

Electronic Control System

 _____________________________________  20 

19.

 

After-Sale Service.

  ___________________________________________  21 

Summary of Contents for ZWY-111B

























Reviews: