Labnet C0226R Page 9 User Manual Download

Page: 9 / 66

Do not position the centrifuge so that it is difficult to operate the power switch

Supply voltage given on the rating plate has to be consistent with local supply

voltage. LABNET INTERNATIONAL laboratory centrifuges are 1st safety class

devices and they are provided with the three-core cable with the plug resistant

to dynamic loadings. Mains socket shall be provided with the safety pin

- protective earth (PE).

It is recommended to install emergency cut-out that shall be located far from

the centrifuge, near the exit or beyond the room.

Before switching on, check whether the centrifuge is connected to power supply

correctly.

Before using check whether the device is correctly intalled.

Current protection

The centrifuge is equipped with current protection (safety fuse). Fuse is situated in

the plug-in socket unit at back wall of the centrifuge.

Safety fuse

Fig.1 Plug-in socket unit

Summary of Contents for C0226R



































































Search results

Summary of Contents for C0226R

Reviews:

Related manuals for C0226R

Brands by name

Popular brands

Labnet C0226R, User Manual

Search results

Summary of Contents for C0226R

Reviews:

Related manuals for C0226R

Brands by name

Popular brands