La Crosse WS-9065U Instruction Manual Download Page 6

TROUBLESHOOTING
NOTE:
 For problems not solved, please contact La Crosse
Technology.

Problem: No reception of WWVB time signal.
Solution:
1) Wait overnight for signal.
2) Be sure Weather Station is at least 6 feet from any electrical

devices, such as televisions, computers, or other radio-
controlled clocks.

3) Remove batteries for five minutes, reinsert and leave the unit

alone overnight without pressing buttons.

4) If there are still problems, contact La Crosse Technology

Problem: Hour is incorrect (minute and date are correct)
Solution:
Be sure correct time zone and daylight saving time settings are
selected.

Problem:  The LCD is faint
Solution:
1) Set the LCD contrast to a higher number
2) Replace batteries

Problem:  No outdoor temperature is displayed.
Solution:
1) Remove all batteries, reinsert into sender first, then display.
2) Place remote sender closer to display.
3) Be sure all batteries are fresh.
4) Place Remote Control Sender and Weather Station in position

so the straight-line signal is not passing through more than
two or three walls.

Problem: Temperatures do not match if units are placed next to

each other.

Solution:
Each temperature sensor is manufactured to be accurate to within
1 degree plus or minus and under normal conditions, so two
sensors could be as much as 2 degrees different. However, the
difference can be exaggerated further because the sensors are
designed for different working environments. The indoor sensor is
less responsive to ambient air currents because of the shielding
effect of the display’s case. In addition, the case can act as a heat
sink to absorb and store heat from external sources (i.e. handling
of the case or radiant heat). Also, the much greater range of the

outdoor temperature sensor requires a different calibration curve
than the indoor range. Error is usually greater at the extreme ends
of a range, making it harder to compare different ranges with
different curves. Under non-laboratory conditions, it is difficult to
compensate for the above factors and obtain an accurate
comparison.

MAINTENANCE AND CARE INSTRUCTIONS

Extreme temperatures, vibration, and shock should be avoided
to prevent damage to the units.

Clean displays and units with a soft, damp cloth. Do not use
solvents or scouring agents; they may mark the displays and
casings.

Do not submerge in water.

Immediately remove all low powered batteries to avoid leakage
and damage.

Opening the casings invalidates the warranty. Do not try to
repair the unit. Contact La Crosse Technology for repairs.

SPECIFICATIONS
Temperature measuring range:
Indoor:

14.2˚F to 139.8˚F with 0.2˚F resolution.
(-9.9˚C to 59.9˚C with 0.1˚C resolution).
“OF.L” displayed if outside this range.

Outdoor:

-21.8˚F to 157.8˚F with 0.2˚F resolution.
(-29.9˚C to 69.9˚C with 0.1˚C resolution).
“OF.L” displayed if outside this range.

Indoor relative humidity 1% to 99% with 1% resolution.
measuring range:

(“- -” displayed if outside this range).

Indoor Temperature checking interval:

Every 10 seconds.

Indoor Humidity checking interval:

Every 1 minute.

Outdoor Temperature checking

Every 1 minute.

interval (Remote Control Sender):
Outdoor Temperature reception

Every 5 minutes.

(Weather Station):
Transmission Range:

80 feet (in open space).

Power Supply:
Weather Station:

3 x AA, IEC LR6, 1.5V.

Temperature Transmitter:

2 x AA, IEC LR6, 1.5V.

Battery life cycle:

Approximately 12 months.

Recommended battery type:

Alkaline.

Dimensions (L x W x H)
Weather Station:

3.974 x 1.22 x 7.04 in
(101 x 31 x 179mm).

Temperature Transmitter:

1.57" x 0.9" x 5.04"
(40 x 23 x 128 mm)

WARRANTY INFORMATION

La Crosse Technology, Ltd provides a 1-year limited warranty on
this product against manufacturing defects in materials and
workmanship.

This limited warranty begins on the original date of purchase, is
valid only on products purchased and used in North America and
only to the original purchaser of this product.  To receive warranty
service, the purchaser must contact La Crosse Technology, Ltd
for problem determination and service procedures.  Warranty
service can only be performed by a La Crosse Technology, Ltd
authorized service center.  The original dated bill of sale must be
presented upon request as proof of purchase to La Crosse
Technology, Ltd or La Crosse Technology, Ltd’s authorized service
center.

La Crosse Technology, Ltd will repair or replace this product, at
our option and at no charge as stipulated herein, with new or
reconditioned parts or products if found to be defective during the
limited warranty period specified above.  All replaced parts and
products become the property of La Crosse Technology, Ltd and
must be returned to La Crosse Technology, Ltd.  Replacement
parts and products assume the remaining original warranty, or
ninety (90) days, whichever is longer.  La Crosse Technology, Ltd
will pay all expenses for labor and materials for all repairs covered
by this warranty.  If necessary repairs are not covered by this
warranty, or if a product is examined which is not in need or repair,
you will be charged for the repairs or examination.  The owner
must pay any shipping charges incurred in getting your La Crosse
Technology, Ltd product to a La Crosse Technology, Ltd authorized
service center.  La Crosse Technology, Ltd will pay reasonable
return shipping charges to the owner of the product.

Your La Crosse Technology, Ltd warranty covers all defects in
material and workmanship with the following specified exceptions:
(1) damage caused by accident, unreasonable use or neglect
(including the lack of reasonable and necessary maintenance);
(2) damage occurring during shipment (claims must be presented
to the carrier); (3) damage to, or deterioration of, any accessory
or decorative surface; (4) damage resulting from failure to follow
instructions contained in your owner’s manual; (5) damage
resulting from the performance of repairs or alterations by someone
other than an authorized La Crosse Technology, Ltd authorized

service center; (6) units used for other than home use (7)
applications and uses that this product was not intended or (8)
the products inability to receive a signal due to any source of
interference..  This warranty covers only actual defects within the
product itself, and does not cover the cost of installation or removal
from a fixed installation, normal set-up or adjustments, claims
based on misrepresentation by the seller or performance variations
resulting from installation-related circumstances.

LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY
FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER
SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR
MALFUNCTION OF THIS PRODUCT.  THIS PRODUCT IS NOT
TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC
INFORMATION.  THIS PRODUCT IS NOT A TOY.  KEEP OUT
OF CHILDREN’S REACH.

This warranty gives you specific legal rights.  You may also have
other rights specific to your State.  Some States do no allow the
exclusion of consequential or incidental damages therefore the
above exclusion of limitation may not apply to you.

For warranty work, technical support, or information contact:

La Crosse Technology, Ltd

190 Main Street

La Crescent, MN 55947

Phone: 507.895.7095

Fax: 507.895.2820

e-mail:

[email protected]

(warranty work)

[email protected]

(information on other products)

web:

www.lacrossetechnology.com

Questions ? Please see instruction video at

www.lacrossetechnology.info/9065

GB

P.20

GB

P.21

GB

P.18

GB

P.19

Summary of Contents for WS-9065U



















Reviews: