Kyocera FS-600 Installation Manual Download Page 63

Page: 63 / 83

Installing the Page Printer

Toner Container Replacement

When the printer runs low on toner, TONER indicator flashes on the control panel. Be sure to promptly

replace with a new toner kit and clean the inside of the printer when this initial message appears.

If the printer stops printing while TONER indicator is lighting, replace with a new toner kit so the printer

can continue printing.

Toner Container Replacement Interval

Assuming an average toner coverage of 5% with Ecoprint mode turned off, the toner container will need

replacing approximately once every 3,600 printed pages (3,000 pages with TK-16).

Toner Kit to be Used

Name:

TK-16/TK-16H (The toner kit included with the printer is the TK-16H.)

Description:

Toner Container

Cleaning

Cloth

Cap For Old Toner Container

Plastic Waste Bag (The toner kit supplied with the printer does not contain a plastic

waste

bag.)

Instruction

Manual

Summary of Contents for FS-600




















































































Search results

Summary of Contents for FS-600

Reviews:

Related manuals for FS-600

Brands by name

Popular brands

Kyocera FS-600, Installation Manual

Search results

Summary of Contents for FS-600

Reviews:

Related manuals for FS-600

Brands by name

Popular brands