Kyocera FS-600 Installation Manual Download Page 59

Page: 59 / 83

Installing the Page Printer

Making sure that the ON LINE/A4 indicator is lit, place a sheet of letterhead paper on the manual

feed tray in the same manner as when printing normally from the manual tray. (The ON LINE/A4

and MANUAL/LGL indicators begin flashing.)

Send data to the printer.

Press the

ON LINE/STATUS

key. (The ON LINE/A4 and MANUAL/LGL indicators stop flashing

and stay lit.)

The printer automatically prints the first page on the letterhead paper on the manual tray, and

subsequent pages on the remaining sheets in the paper cassette.

Returning the manual feed tray

Return the manual feed tray to its original position by reversing steps 1 to 2 (pages 25 and 26).

Note______________________________________________________________________

Be careful not to push the tray back into the printer with the sub-tray folded out horizontally as shown in

the figure.

Sub-Tray

Summary of Contents for FS-600




















































































Search results

Summary of Contents for FS-600

Reviews:

Related manuals for FS-600

Brands by name

Popular brands

Kyocera FS-600, Installation Manual

Search results

Summary of Contents for FS-600

Reviews:

Related manuals for FS-600

Brands by name

Popular brands