24
Basic setting conditioner plate
Basic setting conditioner plate
Basic setting conditioner plate
Basic setting conditioner plate
Position 1
How to change position
How to change position
Position 2
The conditioner plate can be
adjusted to 3 positions with a handle
(see
X
) regardless of its basic
setting.
Beside of that there are 2 other
options;
Pos. 1:
This lower setting is
recommended for light crops.
For more details see operator
manual.
Pos. 2:
This setting is recommended if
problems occur relating to blocking
of the rotor and the flow of the crop
through the machine with heavy
crop.
The conditioner plate is factory-fitted
in position 2.
•
Use an appropriate tool and
remove the pin bolt on both sides
of the machine.
•
Allow the conditioner plate to
drop down on top of the rotor so
there is access between the
conditioner plate and the upper
plate on the machine.
•
Remove the pin bolt shown on
both sides of the conditioner
plate.
•
Move the linkage back on the
conditioner plate as shown and fit
the pin bolt to both sides of the
conditioner plate.
•
Lift the conditioner plate from the
rotor
•
Move the pin bolts on both sides
of the machine to the front
position.
Tine conditioner
X
X
Summary of Contents for 4328LT
