Kustom Signals Raptor RP-1 Operator'S Manual Download Page 83

Page: 83 / 93

SECTION 13—DIRECTIONAL SUPPLEMENT

13.4 STATIONARY OPERATION

13.4.1 STATIONARY ALL

FRONT

FAST

STA

ALL

Indicates the direction of

travel of the strongest

vehicle.

Indicates the direction

of travel of the fastest

vehicle.

To monitor traffic in both directions (the Raptor RP-1 will

automatically indicate which direction the strongest and

fastest vehicles are traveling), repeatedly depress the

MODE switch until “STA ALL” is displayed in the Patrol

area.

When the radar is operated in the Stationary “ALL” mode,

the roadway graphic will display both approaching and

receding indicators. When a target is detected, the

appropriate direction indicator (approaching or receding)

will be displayed above the Target area.

If the “Fastest” function is activated, the appropriate fastest

directional indicator (approaching or receding) will be

displayed above the Fastest Target area.

The example shown is for an approaching 65 mph strongest

vehicle and a receding 80 mph fastest vehicle.

13.4

Summary of Contents for Raptor RP-1






























































































Search results

Summary of Contents for Raptor RP-1

Reviews:

Related manuals for Raptor RP-1

Brands by name

Popular brands

Kustom Signals Raptor RP-1, Operator'S Manual

Search results

Summary of Contents for Raptor RP-1

Reviews:

Related manuals for Raptor RP-1

Brands by name

Popular brands