manualshive.com logo in svg

KUHL Quantron E2, Original Instructions Manual

Share
Download
KUHL Quantron E2 Original Instructions Manual Download Page 27

Operation of the Quantron E2

21

4

4

Operation of the Quantron E2

4.1

Switching on the control unit

Requirements:

The control unit is correctly connected to the mineral fertiliser spreader and 
the tractor (for example, see chapter

3.3: Connecting the control unit, 

page 15

).

A minimum voltage of 

11 V

 is applied.

NOTICE

The operating manual describes the functions of the control unit Quantron E2 

as of software version 1.20.00

.

n 

CAUTION

Risk of injury due to ejected fertiliser!

Only for mineral fertiliser spreaders with electronic control unit

In the case of a fault, it is possible that the metering slide unex-
pectedly opens during road transport to the spreading location. 
There is a danger of slipping and injury to persons due to ejected 
fertiliser.

Before 

transporting the unit to the spreading location, 

always switch off the electronic control unit Quantron E2.

Summary of Contents for Quantron E2













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands