Kubota 2420 Nstruction And Service Manual Download Page 61

Page: 61 / 69

６－１２

Ｒ１

Ａ

ＲＸ

Ｒ２

Maximum Speed (rpm)

４，

０００

Maximum R C F (

１，

７９０

Maximum W

eight (

)

１．

６

Number

wells

Number

Plate

Material

Plate Sizes

Allowable

Speed

rpm

R C F

Buckets

Radius

Allowable

load

gram

９６

２～６

ＰＬ

８６×１２８×５２

４，

０００

１，

７９０

Bucket is

included

with this

rotor.

１０

３４５

９６

２

ＰＬ

The Max. RCF is the calculation value of the Max. speed for the rotation radius of 10 cm.

The value of the RCF that is indicated to the display is showing the value that cut the

lower 2 digits.

Refer to Page 3-12.

The maximum speed drops when the step number increases, although a micro plate is

possible to piling 3 steps.

Refer to Page 6-15.

PL : Plastic

Allowable load per bucket. This load includes the weight of the sample, plate,

adaptor etc.

The weight of bucket is not included in the allowable load.

６－６．

RMP-23 Swinging Bucket Rotor

［１］

Specification

Calculating Centrifugal Force for RMP-23

Because of the size of the micro plate

，

the radius of rotation differs between the center and

the both ends with respect to the rotation axis

，

resulting in the difference in the centrifugal

force

．

The centrifugal force of the place A (cm) Distant from the center of a bucket can be

calculated in accordance with the formula, where the rotation radius R shall be substituted
with the Rx to be obtained by the formula mentioned below.

where

，

：

Radius rotation Minimum

（

）

：

Actual rotation radius in a position which is A cm away from the center of the
bucket

Section 6 Rotor

Ｒ

（

）＝　　

Ｒ

　２

１

（

）＋Ａ

２

（

）

Summary of Contents for 2420






































































Search results

Summary of Contents for 2420

Reviews:

Kubota 2420, Nstruction And Service Manual, Page: 61 / 69

Search results

Summary of Contents for 2420

Reviews: