manualshive.com logo in svg

Kubota 2420, Nstruction And Service Manual, Page: 30 / 69

Share
Download
Kubota 2420 Nstruction And Service Manual Download Page 30

３－１５

100rpm

×

100 g

×

min

sec

SPEED

TIME

100rpm

×

100 g

×

min

sec

SPEED

TIME

FUNCTION

Numbers

Contents

０

「

Speed / RCF

」→「

Timer

」

１

「

Timer

」→「

Speed / RCF

」

［４］

Reverse of setting order of the Speed and the Timer 

The setting order of the speed and the timer can be reversed.
This function is useful when you often operate the centrifuge by changing the 
timer only.
Factory default : 

［

0

］

（１）

Pressing the "SPEED/TIME" knob while holding down the "FUNCTION" key.
The used number of times of the centrifuge is displayed.

（２）

Pressing the "SPEED/TIME" knob several times and let indicate "

" on  the "TIME" 

display. The "SPEED"  display indicates the current setting of the number (see the figure 
below). 

Refer to Page 3-11.

 

［

Ex.

］

Numbers

　

0

（３）

 

Turn the "SPEED/TIME" knob to change the number.

（４）

Press the "SPEED/TIME" knob while holding down the "FUNCTION" key.  
The display returns to the previous Speed and Time indication after the setting (Numbers) 
is saved.

Section 3 Operation

Summary of Contents for 2420






































































Reviews:

No comments