Kubota 2420 Nstruction And Service Manual Download Page 32

Page: 32 / 69

３－１７

100rpm

100 g

min

sec

SPEED

TIME

100rpm

100 g

min

sec

SPEED

TIME

FUNCTION

Numbers

“

SPEED

”

and

“

TIME

”

display

０

After

［

Setting value

］

lights

、［０］

lights

１

After

［

Setting value

］

flashing

、［０］

flashing

２

［８８］［８８］

flashing

３

［－－］［－－］

flashing

４

［Ｅ］［ｎｄ］

flashing

［６］

Setting the Indicators for the end of the operation

Completion of the operation is indicated not only with an alarm but also with the
"SPEED" and "TIME" displays.

The "Alarm Indicators" can be selected from the 5 kinds.
Factory default :

［

］

(see the figure below).

（１）

Pressing the "SPEED/TIME" knob while holding down the "FUNCTION" key.
The used number of times of the centrifuge is displayed.

（２）

Pressing the "SPEED/TIME" knob several times and let indicate "

" on the "TIME"

display. The "SPEED" display indicates the current setting of the number (see the figure
below).

Refer to Page 3-11.

［

Ex.

］

Number : 1

（３）

Turn the "SPEED/TIME" knob to change the number.

（４）

Press the "SPEED/TIME" knob while holding down the "FUNCTION" key.
The display returns to the previous Speed and Time indication after the setting (Numbers)
is saved.

Section 3 Operation

Summary of Contents for 2420






































































Search results

Summary of Contents for 2420

Reviews:

Kubota 2420, Nstruction And Service Manual, Page: 32 / 69

Search results

Summary of Contents for 2420

Reviews: