manualshive.com logo in svg

Kubota 2420, Nstruction And Service Manual, Page: 56 / 69

Share
Download
Kubota 2420 Nstruction And Service Manual Download Page 56

６－７

Do  not insert  the  cushion  upside  down  or  in  a 
slanted position, otherwise, the glass tube  may be 
damaged or you may not be able to remove it.

Cushion for 15ml Glass tube

Bucket

Code No.024-2610

(Bucket Code No.053-7340)

Code No.024-1400

(Bucket Code No.053-4990

053-4910, 053-4900
053-4980)

Cushion for 50ml Glass tube

Code No.024-3190

Bucket

［４］

Cushions / Adapter

When glass tubes are used, be sure to use the cushion to avoid damage.
Insert the cushion  into the tube rack so that  its concave side faces 
upward. 
If a glass tube is damaged, replace the cushion.
If broken pieces  of the glass tube are contained  in  the cushion,  the 
glass tube will be broken again.

（１）

Cushion for 15ml and 50ml Glass tubes

      How to place 15ml cushion

①

Place  a  cushion  in  the  bucket  with  the 
concave surface facing  upward.

 

②

Fully insert the cushion to the bottom of the 
hole using a glass tube.
(the edges of the cushion  bend to prevent it 
from coming out.)

      How to place 50ml cushion

　

Place  a  cushion  in  the  bucket  with  the 
concave surface facing  upward.

Section 6 Rotor

Glass tube

Bucket

Cushion

Summary of Contents for 2420






































































Reviews:

No comments